Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> My 400 sbc survived the cam break-in!
User Name
Password
lost password?   |   register now

Thread: My 400 sbc survived the cam break-in! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-28-2013 08:33 PM
SPEED MASTERS CC Here is the video link.

408 SBC CAM BREAK IN - YouTube
05-26-2013 07:45 PM
vinniekq2 20/50 is a good all round viscosity.You can adjust viscosities in accordance to build clearances and severity of engines use.
05-26-2013 07:21 PM
SPEED MASTERS CC Is Valvoline VR1 20/50 wt ok to run?
05-26-2013 11:31 AM
vinniekq2 post a video.The easiest way is to start a youtube acct and follow their instructions,then just post a link
05-26-2013 11:25 AM
1Gary No synthetics for the life of the engine.A race oil like Joe Gibbs for every oil change after the break-in.We have seen lobe failures many miles later with the wrong choices.
05-26-2013 10:47 AM
SPEED MASTERS CC The carbs are 500 cfm (each). The intake is the old edelbrock c-26 (for looks). The linkage is progressive. I did not touch the carbs! They ran great for the break-in. (The engine was run on a break-in stand.) The block is filled with hard block to the side freeze plugs. It ran cool the whole time at 180 ish. The heads are world products sportsman 2's, I know they are sub-par head today, but I had these in stock and they were professionally pocket ported. This whole motor was done on a pretty tight budget and still cost a lot... The cam is from comp. It is a custom grind. The springs are from Howards: Dual type with 135 on the seat 285 open pressure. I ran these springs with comp stainless 1.6 rockers. This is my first complete motor build I did myself. I used a chevy Z-28 oil pump and matching pan with tray from G.M. I used arp fasteners on everything. I now want to convert the carbs to run on E-85. The only carb guy that I could find that does edelbrock conversions is in Minnesota at a cost of $300 each! Ouch! I cannot find kits or info on how to do the work myself... I was told the carbs are too small for this size engine, but they are what I had purchased from another club member for a great deal. So, I ran what I had" ... I am planning on putting on 1 inch carb spacers next. I have the break-in video from a smart phone that looks great, unfortunately I am currently not smart enough to know how get the video to post here. I sent it to my email, but that is as far as I got with it...

Again thanks to the everyone on the forum, your posted info helped a bunch. Most of the guys in our club did not think the engine combo would work as well as it does. I am pretty stoked!
05-26-2013 10:13 AM
camaroman7d You ran full spring pressure for break in? I am assuming you have dual springs.
05-26-2013 05:27 AM
Richiehd Who's cam?
05-25-2013 09:47 PM
vinniekq2 what kind of heads? post a video
05-25-2013 09:01 PM
ap72 Impressed you got that lift to work out a d edelbrock carbs to run well with that duration. Which carb model? They can be tricky with larger duration cams.
05-25-2013 08:57 PM
SPEED MASTERS CC
My 400 sbc survived the cam break-in!

I broke in the cam with valvoline vr1 20-50w and a bottle of lucas break-in additive. I was sweating it big time! The cam is a flat tappet .575 lift 250 duration @ .05 on a 106 lsa. 11.7-1 comp. As soon as the engine fired I revved it to 3000 rpm. I fluctuated the rpm from 3000 to 2500 for 30 min. This a budget type motor. 200 cc heads, flat top claimer pistons, stock crank, eagle rods, msd ignition, dual edelbrock carbs.The more I work with the edelbrock carbs the more i like them... I ran the motor on 110 octane gas. We have about 30 guys in our car club that all use this form. Thanks for all the past help!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.