Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> 4 bar suspension mock up
User Name
Password
lost password?   |   register now

Thread: 4 bar suspension mock up Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-25-2013 11:23 AM
67-4-fun Thanks for all the input. Right now the body is off the frame as I'm redoing the whole car. After doing more search I think most agree that the bars need to be more level. in order for me to level off the bars at ride height i want, going to have to raise the crossbrace to raise front bar location. i know what tire I want to run which is 30 inch . My plan is to slam the car down and tuck the tires slightly under wheel wells. I believe that would be about 3 or 4 inch drop from a factory setup. I know pretty much know where centerline of axle housing needs to be in relation to frame and body to get the look I want and have room for suspension movement and tire expansion. So I will do some more modification. I didn't want to back half the car as I think the 67-68 look better with mini tubs. Mine is tubed 2.5 inches.
06-25-2013 09:19 AM
kso It's good you're not trying to use the other type on the street. If adjusted to where the "instant center" is very far out, the stresses on the housing can be enormous, a good pothole can tear a bracket off the housing.

On your setup if the bars run downward from the chassis to the axle, it increases anti-squat but also causes the rr axle to steer into corners with body roll which is really bad for high-speed stability. Having the bars angle up from the chassis to axle, stability is better but it's going to squat more at launch. As is being said, for your use the best compromise is probably straight level.

It would be worth doing enough research on, that you're dead-certain by the time you get the welder out.
06-25-2013 09:03 AM
NEW INTERIORS On your four bar set up the bars should be close to level with the ground... One bar won't be level and the other at a angle,, Your right about that,, It isn't a four link... When setting it up at ride height set them as close to level with the ground as you can.. Then set the cross bar where needed..
06-25-2013 07:34 AM
delawarebill
4 link

if u have an idea of the angle of the trans then u can get very close to the correct pinion angle u need.. set the pinion angle then level the bars and weld the bracket to the axle.. when i built my bucket i also wanted 4 link.. so i built mine with all adjustable points... boy was that nice when aliening up wheels..
06-25-2013 01:37 AM
67-4-fun I can not adjust the bar angle by changing location holes on the brackets like a typical 4 link. The bars are fixed to where they are attach to crossbrace and to the brackets on housing. In order for me to level off the upper and lower bars for the current ride height i want is to raise the crossbrace between the frame rails which not a big deal as its just spot welded for mock up. Just trying to figure a all around starting point. This car is a 60/40 street strip car prostreet in mind.
06-25-2013 01:22 AM
blwn31 I believe the lower bar should be parallel to the ground when the suspension is statically loaded.The upper bar would then be used to tune the suspension, by raising or lowering the forward mounting pickup point.

Keith
06-25-2013 01:15 AM
67-4-fun
4 bar suspension mock up

Hello guys,
I bought a 4 bar rear suspension setup similar to 4 link with out different location for bars for my 67 Camaro. See pic of my 4 bar below. I'm currently mocking up setup to the riide height I want as if suspension loaded. My question here is the lower bars are at a 12 deg down ward angle from front to back. Is this to much? Or should the lower bars be more level? Your thoughts to the guys that know 4 bar setup

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.