Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Gear Tooth Pattern on Ford 9"
User Name
Password
lost password?   |   register now

Thread: Gear Tooth Pattern on Ford 9" Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-05-2013 07:40 AM
1low37
Update

Thanks for the advise. I reassembled the unit with the shim that came with it and the .014 BL that I measured before starting this journey. I took a bright flashlight and peered around inside the posi unit and found some small chips on the spider gears. SO my fears that I got hosed in this transaction are most likely true. I put it in the truck and drove it around a bit; aside from what I think is an e-brake shoe on backing plate squeak it seems ok. But no freeway miles yet.
I am now hoping it stays together long enough to save up for a proper diff build. All I can hope for is it doesn't come apart catastrophically. Hopefully there will not be an eulogy on this one.
07-05-2013 07:11 AM
cranky1 I like to paint the pinion and not the ring. It gives a more pronounced read than painting the ring with the checking grease does.
06-23-2013 04:54 PM
big gear head First of all you are trying to do the impossible. You can not get a text book pattern on used gears no matter how hard you try. These gears have wear on them and there is no way that the pattern is going to look like what you think it should. Most of the time with used gears I try to get the coast side to look good and don't worry about the drive side. This is because the drive side has much more wear on it than the coast side and you are more likely to get a good looking pattern on the coast side. In your case it seems that both the drive and coast have enough wear on them that you can't get a good pattern on either side. This is why I try to do a backlash and pattern check BEFORE I take anything apart so that I know what I need to be looking for when I put it back together. I think in this case I would use the original pinion shim and hope for the best.
06-23-2013 01:55 PM
1low37
Gear Tooth Pattern on Ford 9"

Hi Guys, I have been trying to get a "good used" Ford Posi 9" diff set up correctly and cannot seem to get the drive and coast patterns in the middle of the ring gear. Specs, Reusing the bearings as they appear ok. Ring gear run-out is about .002-.003" Changed the yoke and used a Ratec supersleeve. Pinion bearing torque is 7 in-lbs, 3.25 gear Ratio, factory (or at least what came out of it was a .018 pinion carrier shim.
I have been up and down the shim stack spectrum-from . 000 to over .025 and nothing seems to get the pattern off the toe of the coast side; without really screwing up the drive side. I have posted pictures of the (factory .018 shim) pattern first, with .012" backlash. Then with a .015 pinion shim with .013 backlash, which seems to center the drive side up nicely but still does not get the coast side up the middle much. Its driving me crazy. I have tried so many shim and backlash settings I am cross-eyed . I just wanna go for a drive in the hotrod. I have seen a pattern in the Yukon Gear set-up article and it shows a pattern much like this one with the drive centered and coast biased towards the toe and they say its OK. Any suggestions?
Thanks 1low

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.