Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Drip rails
User Name
Password
lost password?   |   register now

Thread: Drip rails Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-10-2005 10:03 PM
troy-curt Well it's been two years now, I wonder if he ever got the job done?

Troy
02-10-2005 09:27 PM
racur96 I bought some new brake line and cut flared part off and welded them in and then applied filler on top of the line.
10-28-2003 10:24 PM
crazy larry my next best guess would be all metal filler.........

that stuff evercoat makes.

and if your worried about the amount of filler, you probably could weld in a small filler piece with a thin coat of filler on top for smoothness...... just like you said.
10-28-2003 09:42 PM
alronz
Drip Rails

Thanks for the input guys. Again however I want to emphasize I am not interested in cutting the rails off. The Drip rail stays in place is filled & molded into the roof line with a nice flowing radius. I have done test spots & get seperation @ the roof line & drip rail both. It may have to do with the extreme heat as I live in Las Vegas & it's hard to tell how hot a black trucks surface gets with that desert sun beating down on it, but the expansion of the metal over time causes seperation of the materials.
I am seeking other ways to fill it that will stand the stress & expansion csused by the extreme heat here.
Bondo failed, fiberglass resin failed the test. other options?
1 old fashioned lead ?
2 metal to metal aluminized bondo ?
3 ???????????
10-28-2003 09:32 AM
troy-curt I cut mine off and welded the roof back on like larry and dragon did there's.

If you get the area clean and the metal roughed up, you should be able to fill it with bondo. It would take a lot of twisting and flex to crack it. I've seen bondo a lot thicker than that on customs and it stayed alright.

Good Luck
Troy

10-28-2003 08:19 AM
alronz Thanks for the replys guys.
I just don't care to shave them as in my opinion they add a lot to the eyebrow effect the 56 roofline has compared to the 53 - 55s
10-28-2003 07:11 AM
Dragon J I shaved mine on tmy Henry 'J as Larry described. I don't think there is any way to avoid the cracking unless you weld them- just take your time and jump from side to side. (jus my $.o2!)
10-27-2003 06:17 PM
crazy larry hey. i have a 72, and couldn't even begin to imagine the difference between your truck and mine, but what i did was; i cut the drip rails off with a sawzall, and welded it back up, tack here, tack there, til it was solid. no warpage whatsoever. but i did burn through a few places that required added welding and grinding. i would guess there's less then an 1/8" of filler on it now.... i like the difference, but i wonder if the average joe would even notice the change?......
10-27-2003 02:28 PM
alronz
Drip rails

Iwant to fill the drip rails on my 56 F100 & radius them into the roof area.
What is the best method for doing this that will not result in hair line cracks at either the drip rail or the roof.
As tests I have tried bondo & fiberglass but the both have seperation problems. I assume this is due to the thickness of the fill.
Would the old standby of body lead work best?
I could make a 16ga. strip & weld the entire thing in but would prefer not to do that much welding due to warping problems.
TIA

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.