Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Ground Clamp on welder makeover?
User Name
Password
lost password?   |   register now

Thread: Ground Clamp on welder makeover? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-16-2013 01:17 PM
1971BB427 I also had trouble with squeezing my ground easily, so I went another route. I welded a tab on an old pair of vise grips and bolted the ground cable to the vise grips. I can adjust the jaws for various thickness metal, and once clamped it stays put. Easy to release, and on small parts I can use the vise grip clamp to hold the part as I weld it too.
09-14-2013 10:55 AM
HotRodMan
Rebuilt old ground clamp

I went to the local welding supply and tried that Tweko ground clamp and the spring was so strong I could hardly squeeze it. I have arthritis in my hands so I wanted to rebuild my old one. I have installed the new copper strap and it works good, and I don't have to worry about it working loose.
09-14-2013 10:32 AM
timothale
grounding

I ve used copper pipe pieces for fillers. I have a fine wire wheel that I clean- buff parts with first, a little bit of invisible corrosion caused all kinds of problems with my old Tig welder. On welding tips and tricks.com Jody shows using a 1 ft long piece of bare stranded old ground cable as an extra ground, HE sometimes wraps it around the part and says he doesn't get the ground burn spot on the part. and says a lot of Mig problems can be caused by inadequate ground. I tried one of those HF magnetic grounds, it only worked for a while. It probably needs to be taken apart and cleaned,
09-14-2013 04:43 AM
jonahb If it was me I would just throw away that ground clamp and spend 20-30$ and get a good tweco replacement.
$22
Amazon.com: SEPTLS35892051320 - Tweco Ground Clamps: Home Improvement Amazon.com: SEPTLS35892051320 - Tweco Ground Clamps: Home Improvement

$31
Tweco Ground Clamps Model Code: AA (part# 9205-1120) - Amazon.com Tweco Ground Clamps Model Code: AA (part# 9205-1120) - Amazon.com
09-14-2013 01:27 AM
OneMoreTime None that I can think of..Sometimes we even bolt the ground lead to whatever we are welding..I have seen a C-clamp used as a ground clamp as well..

Sam
09-14-2013 12:04 AM
HotRodMan
Ground Clamp on welder makeover?

I have a Lincoln pro 180 220 volt welder. I had problems welding with it and determined the problem was that serrated copper strap in the ground clamp. I repositioned it and it works for now but doesn't look like it will last.

Is there any reason I can not replace that by taking a 1/2 inch copper pipe, crush it flat in a vise, grind off each side, which would give me two flat pieces of copper, take one of the flat pieces of copper and install it in place of the old serrated copper strap that keeps working loose?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.