Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 4l60E will not move
User Name
Password
lost password?   |   register now

Thread: 4l60E will not move Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-14-2013 05:25 AM
jokerZ71 A regular filter/fluid change only changes about half you fluid,so,run it a few hundred miles & do another filter/fluid change.DO NOT FLUSH !!!
10-14-2013 12:54 AM
C-cab dreamer You did mention that the tranny fluid was burned. There's always a reason for that, and whatever the reason is - it isn't good. Burned hydraulic fluid doesn't work the same as new, and if you expect to get another few thousand miles out of your vehicle, you should change it and the filter PDQ.
10-12-2013 08:13 PM
Line626 Thanks for all the help! ill keep on truckn my friends!
10-12-2013 07:07 PM
markdavid yep , save for a build and eeeaa****yyy does it on the thing for now !!!!
10-12-2013 06:55 PM
ssimpala Do NOT flush it. With that mileage it's probably badly worn and you need those little grains of clutch fiber to keep it going for a while...but plan a rebuild soon.
10-12-2013 05:26 PM
Line626 update.......... I replaced filter and now it has the right pressures and truck is rolling again. Now since the miles are high should I do a transmission flush or just run it like it is? which is better for my situation? im saving up for a complete rebuild by the way.
10-12-2013 12:54 PM
Line626 the mileage is correct. im in the process of doing a filter change now.
10-12-2013 12:00 PM
Crosley if the 205 k miles are accurate on the transmittin, it is worn out twice.

The filter may be clogging up, to cause full loss of pressure.

have you dropped the pan? A filter change is not expensive, may be worth the effort as a test.

when removing the pan from trans in that truck, be careful with shift solenoids. You can break them trying to get pan off trans around exhaust pipe IF the pipe crowds the pan as most GM trucks
10-12-2013 10:11 AM
Line626 update........ I put a guage on the test port, checked fluid level on cold truck, then started truck and checked fluid again and it dropped. then checked guage, guage fluctuated 60 psi in park, 80 psi in reverse, and 60 in all other gears. then after warming up for a few minutes guage fell to zero in all gears.
10-12-2013 08:25 AM
Line626
4l60E will not move

hello, thanks in advance for all comments and ideas! 2002 chevy z71 205,000 miles, I have no forward and reverse movement. i made sure transfer case was in gear, so then I checked the fluid it was a lil above full dark in color and smelled burnt. I came to this forum and read through trying to find ideas and info. then I did some tests that I read. checked o2 sensor fuse its good, unplugged mass air flow sensor no changes, unplugged test port above linkage I have a good stream of fluid [going to get a guage]. I jacked up rear put it in gear and tires started turning to idle speed, then I applied accelerator up to 2500 rpms and speedometer fell to zero no rotation of tires. I left it in gear [drive], after 5-10 minutes heard a click and tires started rotating to idle speed the immediately back to nothing. it did this several times. any ideas or suggestions would be greatly appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.