Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Dent
User Name
Password
lost password?   |   register now

Thread: Dent Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-04-2002 09:15 PM
ponchowerx Can you get a prybar behind there and bang it out with a hammer? [I assume your jack is alot bigger]. If not try to tack weld a piece of metal[angle, flat bar on edge] to the dent, drill some holes in it and yank on that instead, either by a chain or bars inserted into the holes or even your slidehamer. A pull on a larger area will help on this hard dent.After just grind it off. Just my .02
10-02-2002 07:45 PM
Halloweenking Most any welder will work if you know how to use it, but arc is fine.

Carguy is correct, most large dents will need to be pulled more than once sometimes several different places. Went dents form metal around the dents strech they don't just cave. If you plan to try to pull the dent you must pull in several different spots as well as shrink the steel back into shape. There are a few methods of doing this but none are for the beginner. If you try to pull the dent and do it in several different places try dry ice. Pass a chunk of dry ice by the outside of the dented area, the dry ice will cause the steel to contract and sometime the dent will pop itself out depending on size, direction of dent and place on the body. This is the only "safe" way to do this without the aid of an exsperienced bodyman. Other methods are normally used, but to the newcomer they are not recomended do to difficulty.

HK
10-02-2002 07:24 PM
CARGUY one dent will need to be pulled in several places thruout not just one
10-02-2002 03:09 PM
bjam2 Would an arc-welder work?

When I try to pull out the dent with the slide hammer type dent puller it just makes a little mound.
10-01-2002 12:11 PM
Halloweenking replacing the panel you described is not very hard. The tools you'll need are a mig welder prefferably, sanding supplies, wheel cutter or saws-all. Cut the old panel off, well the new one on, grind welds smooth, smooth with body filler and prime/seal and paint and your done. If you need a step by step let me know, I'll do what I can to teach you how to do it.

Replacing a entire body panel isn't something to start out on, do you have any body men/women to help you? If not, have you checked around for better prices at bodyshops? If not let me know, I'll do what I can to help you.

HK
10-01-2002 11:45 AM
bjam2
Dent

There is a dent between the wheel and door in my 85 el camino.

I took it to a body shop and they said they couldn't do anything and it would cost $1100 for a whole new panel put on.

I tried to pull the dent with a screw in dent puller but it didn't work. The body shop also tried a suction cup puller which did nothing.

Someone mentioned jacking it out for inside the car (in the cubby) but there is a inner piece in the way.

What should I try next?

I am not very experienced with body work how hard is it to replace the whole panel?

What tools would I need?

Any other advice?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.