Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Dropped Axle
User Name
Password
lost password?   |   register now

Thread: Dropped Axle Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-27-2003 07:45 PM
adtkart Must need the bottom of my glasses to see that. Actually, I looked in the book to see if they showed it. The picture that they have actually has no detail that helps for assembly that I can see, specially since I am using their spindles and axle. They don't use the clips like are used on u-joints. Thanks anyway.
12-27-2003 12:26 PM
Igosplut theres also a breakdown of the assembly in the catalog. Its small, so you have to look close for it.....
12-23-2003 07:01 PM
adtkart Thanks Willys. I figured you'd know. That was basically what I was thinking after I posted. Just hoped someone that knew for sure would set me straight. I am used to having things that I don't know where they are, but not having things and not knowing where they go.
12-23-2003 08:47 AM
willys36@aol.com You guessed right about all the parts you mentioned. The felt ring is slipped on the king pin before you install it and ends up just under the head of the pin and acts as a grease retainer/dust seal.
12-21-2003 09:08 AM
poncho62 Just guessing, as I have never built that type of front end. I think the felt washer is a grease seal, so all the grease doesn't run out. About the holes, if both of them go through to the king pins, I would put grease nipples in both of them. The better the lubrication, the better.

Like I said, just guessing....will probably be proven wrong.
12-21-2003 08:52 AM
adtkart
Dropped Axle

I have a 4" dropped axle set-up from Speedway. I ordered the spindles and king-pins from them also. The question I have is on the assembly, since they came with no instructions. In the king pin set, there are 2 felt washers and metal "cap like washers". I understand that the bearing goes on the bottom of the axle between the spindle and axle. There are a couple of thin shims that came with it, and I am guessing that they are for on the top of the axle/spindle area for fit. Where does the felt piece go? The spindles have 2 tapped holes in the top and bottom where the king pin goes thru. One appears to be for a grease fitting and the other for a set screw. Does that set screw just plug that hole, and not get tightened down on the king pin? There is a set screw on the axle that, I think, holds the king pin in place.

Am I doing this right?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.