Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Check my 383 combo..I need help
User Name
lost password?   |   register now

Thread: Check my 383 combo..I need help Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-17-2004 03:22 PM
lluciano77 You will be able to run pump gas for sure with that combo. I have an 11:1 400 with iron heads, 234o of duration, and 36o total advance, it doesn't ping. I can only get 91 octane in my area too.
01-17-2004 10:41 AM
terror385 hi guys

I will use complete 4340 forged bottom end

with AFR210 or canfield220 or DART PRO 1 CNC

and ofcourse I will use a deep pan

Did you say your going to put juice/nos to the 383?
I intend to spray 250 - 300 hp shot of nitrous

01-17-2004 09:07 AM
tm454 I like Edelbrock carbs. I run the stock oil pump but a deep pan looks cool and requires a special oil pump pickup installed on the pump, available at Summit installed. The 2400 stall is sufficient. I don't use anything extra to seal the intake but the gasket and torque to specs. The cat crank for a 400sbc is inexpensive and I haven't had any problems with mine, will require a machine shop to setup the crank, rods for clearance and ballanceing the rotating assembly. If you haven't done it before have the engine/machine shop gap your rings and space the crank and rod brngs for proper clearance. Did you say your going to put juice/nos to the 383? You would have been better off using the stock 350, but thats just my opinion, your going to blow up your engine eventually so why waste all that money on a 383 just to have to do it all over again when it blows??


Rat Rods Rule!
01-14-2004 09:19 AM
Thom Laybourne
More Parts

What crank are you going to use? Are you going to use rollers? Heavy duty oil system? Timing gears or chain? Sump pan? Carb 650? Headers? What shape piston? 2400 Stall TC? 342 gears? Posi rear? Spacer helps.

Hope this helps.

01-13-2004 08:33 AM
terror385 hi

you are right the CR seems to be high
but I've calculated the DCR
it is very low = 7.92 (I assumed that the ILC=112 )

thanks bro

it was my fault to post it here

can anyone move this to the ENGINE forum
01-13-2004 07:31 AM
406chevelle Looks like a pretty nice combo to me, but I am no expert, wait and see what the real pro's say.

I do know that you will not be able to run pump gas at that C/R.

01-13-2004 02:19 AM
terror385 bump
01-12-2004 03:26 PM
Check my 383 combo..I need help

can you help me please in my first engine ??
I am planing to build a 383 stroker for my weekend ride (83 camaro)

here are the specs

chevy 350 block bored to 4.030
all forged rotating assy. with 6" rods
CR 11:1 approximately

Canfield aluminum 220cc

Victor Jr ( is there any benefit of using spacers )

need help

HEI with MSD 6AL

Crower solid roller for nitrous # 00552
Advertised Duration: Intake 290/ Exhaust 296
Duration @ .050": Intake 254/ Exhaust 262
Lobe Lift: Intake .391"/ Exhaust .408"
Gross Lift(with 1.5 rocker arms): Intake .587"/ Exhaust .612"
LSA : 114
intake centerline: ???? I don't know

converter ????

gears ????

is this a good combo ???
can I use pump gas with this CR??
can you estimate the horsepower & torque for me please?

Any comments are appreciated


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 01:43 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.