Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Q-Jet wont idle?!?
User Name
lost password?   |   register now

Thread: Q-Jet wont idle?!? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-25-2004 11:01 AM
Jmark A vacuum leak will not cause the engine to rev that high unless there is a huge amount of excess fuel going into the engine too. If the carb is moderately rich, an air leak will cause a slight increase in idle speed. If the carb is on the lean side, a vac leak will cause the idle speed to decrease.

Check to make sure that the choke fast idle cam is not holding the idle up. The fast idle screw us down under the choke housing facing foward. If someone set the fast idle up too high with a wrong choke setting, then with the correct choke setting, the fast idle will be sky high.

Look down the secondaries and make sure the bottom butterflies are COMPLETELY closed.

Same with the primaries, look down and make sure they will close completely when the choke fast idle cam is pushed all the way down. If its NOT completely closed with the idle mix screw backed out and the choke cam down, find out why. Usually, its the fast idle screw adjustment.
01-25-2004 08:04 AM
reborn55 make sure the choke unloader is not jammed holding the secondary throttle plate open a little bit./ meant to say the scondary throttle lock out can cause the secondary throttle plate to stick partially open. Will cause similar symptoms
01-24-2004 10:25 PM
87442lover A vacuum leak causing THAT much of a reving problem though? I mean it sounds like someone has their foot mashed down on the pedal or something, but the throttle is still in idle setting. But I will check it tomorrow.
01-24-2004 09:37 PM
badknuckles bingo
01-24-2004 09:23 PM
reborn55 Sounds like you have got a big vacuum leak. are all your vacuum ports in use. large one in back to booster and a couple in front--one to the pcv valve. May be set to lean, metering rods stuck down in the jets, mixture control solenois not working. Would check for vacuum leak or wrong base gasket first.
01-24-2004 04:02 PM
Q-Jet wont idle?!?

Hey, I finally got the chevy Q-jet back together and installed. The problem is that as soon as I turn the ignition it revs to about 3K RPM for around 5 seconds and then dies. I can't get it to idle and I cant get it to stop reving so much when I turn the key.

Has anybody else had this happen after a rebuild, and anybody got any idea of what is wrong?


Oh yeah, I checked the secondaries and they dont seem to be opening at idle or anything so that doesnt seem to be the problem. The choke is also pulled wide open as soon as the motor turns over because it revs so high and creates alot of instant vacuum.

84 monte carlo 305 HO.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 11:38 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.