Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Cab mounts
User Name
Password
lost password?   |   register now

Thread: Cab mounts Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-28-2004 11:38 AM
Gearhead forever Many thanks!
01-27-2004 11:05 PM
M&M CUSTOM The cupped metal reinforcements are .125 inch (1/8th-inch) stamped pieces. They are included in the set, the square washers are just washers the factory used to spread the support of the mount over a greater area, and they are 1/8th inch too.
01-27-2004 10:02 PM
Gearhead forever Excellent..Thanks M&M. the mounts look right. Do you know if the "shaped metal retainers/washers" are those really heavily cupped stamped pieces (mushroom shaped) or just a large dished washer? thanks again.

Gear.
01-27-2004 02:29 PM
M&M CUSTOM In 1981 when GM redesigned the Chevy/Gmc trucks one of the few changes was to the body mounts to make them more flexible.
In changing them GM also went from a seperate 2 and 4 wheel drive body mount style to a simpler mount that was used on both C and K series trucks (and R & V series 88-91 trucks after the complete redesign for the 88 body style)
I scanned one of my catalog pages and added a couple things for reference.
01-26-2004 08:16 PM
Gearhead forever Oh good...the instructions that came with them?? Not, Nada, Nil, Zilch....
I bought them from a local supply house. They order them from Canadas largest autobody panel supply companies, Cross Canada. (Yeah...there is my 1st mistake..) The catalogue carried only one size of mount for front, rear or rad location for this year. The only size difference specified was with the 2wd vs. 4wd models. Should I have gone with the polyeurethane rather than the regular rubber style? Any advice would be extremely appreciated, as I'm hoping to drag this thing home this week if possible...if this weather lets up.
01-26-2004 06:06 PM
bullheimer i'm pretty sure you are supposed to reuse the washers and some other hardware but buy new washers at least. just follow the directions that came with them and you will be okay regardless of what they looked like stock.
01-26-2004 04:41 PM
M&M CUSTOM What brand mounts did you buy, are they stock replacement rubber or polyurethane?
Which mount are you referring to specifically, the radiator support mounts, the front cab mounts or the rear cab mounts, as they are all diferent in shape and size.
you also have a difference between the 2 and 4 wheel drive versions of all of these mounts, if the rest wasn't confusing enough.

I have the information you need for all of this stuff.

I'll see if I can scan a couple pics for reference later.
01-26-2004 11:42 AM
Gearhead forever
Cab mounts

I bought some new cab mounts for my '87 Chevy p/u.
They are an aftermarket item and are different from the originals. (The original had a mushroom shaped steel shoe)They only consist of the upper and lower rubber bushings, the upper with a steel insert and plate cast into the rubber. The bottom bushing is only a ring of rubber which obviously requires a retaining washer. I'm wondering if I can reuse the original washer, and how much the lower rubber is supposed to collapse? Is it designed to fold over on itself? (This frame off project has gone on so long that I can't recall how the thing looked when I tore it apart.) Any help would be appreciated as I may get stuck in town tonight due to bad weather, leaving me a window of opportuniny. (for assembly that is)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.