Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> IFS installed on 57 F100
User Name
Password
lost password?   |   register now

Thread: IFS installed on 57 F100 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2004 05:10 AM
Centerline There are a couple different strut rods. As I understand it the Pinto strut rods had a slightly different bend in them than the Mustang rods. This may be where your problem lies.

Usually all you have to do is heat the strut rod with a torch and make the necessary bend to line up with the frame.

Hope this helps.

Centerline
02-20-2004 12:53 AM
deuce_454 i have installed an OEM MII in my 32 roadster, and i have cut the strut rod and welded on a tube that holds a bushing to gain some room arround my engine. but the mountings are still on the inside of my frame

i think you should re do it to get the pivot point right, because unless you have a very stiff front suspension that hardly mooves you are going to get some funny allignment changes throughout the travel of the wheel. The easiest is propably to buy a triangulated lower contrill arm that elimitates the strut rod. that will also loose some of the sloppyness the SOFT strut rod bushings add.
02-19-2004 08:13 PM
Darkman270 I was unable to line up the lower control arm pivot with the rear strut rod mounting point which is actually a pivot too. This was due to my frame width. I could have, as Willys36, did put a factory rear strut mount that was widened. Ideally a piece of 1/2" allthread running through the lower control arm bolt holes should also shoot a bullseye through the rear strut mounting bracket.
02-19-2004 07:54 PM
RAW
What did you mean by...

" I am not happy with the strut alignment with reference to the lower control arm pivot bolt but I worked with what I had."

Are you discussing the parallels with the lower arm shaft and the upper arm mounts. While bench assembling I was concerned about the "anti-dive" and the upper arm shaft. I'm installing a stage III but curious about your comment.

thx, r
02-16-2004 09:18 AM
deuce_454 looks great. but while you are at it i would go ahead and box the rest of the frame, it will improve your ride emensly, it will stiffen the rails many thousand times. and make for a much more modern ride (an x member wont hurt either- but boxing is cheap and easy in your stage and will help alot)
02-15-2004 02:16 PM
Darkman270 Thanks for the comments guys. One day I may build a real rod as opposed to rebuilding a stocker. I envy the latitude you have when it comes to mixing and matching parts. I need to keep mine stock APPEARING to keep with my project mission. Don't get me wrong I'm enjoying it but sometimes I feel like I'm in a box. A very small box. LOL
02-14-2004 07:21 PM
jalopy45 Nothing wrong with the gussets! It may be overkill but that is a good thing, Go ahead and drive it everyday. Looks like you got a good start on the chassis.
02-13-2004 02:06 PM
RAW
IFS Gussets

I'm still bench assembling my Fatman Stage III but my plan is to add the frame inboard and outboard gusset as you have installed. In fact I making cardboard "go-bys" for the shop. r
02-12-2004 09:22 PM
Darkman270 Here is second picture.

If someone can tell me how to put the image in the text it would be nice.
02-12-2004 09:17 PM
Darkman270
IFS installed on 57 F100

I am truely a brave man to post these pictures. I know that I will be told what I did wrong. Really I appreciate the criticism so don't hold back. First I'll say that I added a triangular box to the top of the Fatman crossmember. It is welded to the inner boxing plate that we installed. It is 1/4" wall. I felt like it would reduce the frame flexing strengthening the overall design. I am not happy with the strut alignment with reference to the lower control arm pivot bolt but I worked with what I had. This will not be a racer or daily driver and will see infrequent trips out on mostly good roads. We also added a gusset to the strut rod mounting bracket. I am open to suggestions on how to improve this. Here are a few pics .

OK I guess I can only do one at a time.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.