Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 351 Cleavland valve seals
User Name
Password
lost password?   |   register now

Thread: 351 Cleavland valve seals Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-28-2002 03:43 PM
dmorris1200 I used the air method on an old 302 I had. I never set the engine to top dead anything. Took off the valve covers, removed one spark plug at a time each time screwing in an adapter from an old compression gauge I had, and with an air line connected with a regulator keeping the pressure to about 50 psi or so (don't remember exact amount-been a few years) backed off the rockers and removed the springs. Worked my way around the whole engine in no time and ran that puppy smoke free for a few years after that. Not a bad idea to remove the oil pan when done if you can. I found a few valves with nothing left of the old seals, guess where those pesky little pieces of the old seals went to .

[ October 28, 2002: Message edited by: dmorris1200 ]</p>
10-28-2002 03:36 PM
BstMech K-D is what I use now (with the screw and fingers), they are strong enough to smack with your palm to break the keepers. Those cheap ones (Auto Zone brand) aren't worth a crap unless you're very careful with'em.
10-28-2002 03:08 PM
slider I like that rope trick Best Mechanic. Having had the engine take off with the air pressure is exciting to say the least. At best you won't bleed when you hit your noggin on the hood so you can get a beer down quick. Last time I looked KD made the valve spring compressors for most everything, even some universals.
10-28-2002 02:48 PM
BstMech You can also jam a bunch of 1/4-5/16" rope into the plug hole (with piston in a lower position) After you have a lot of rope (at least a couple of feet) jammed into the cyl. (make sure to leave some hanging out so it can be removed later <img src="graemlins/drunk.gif" border="0" alt="[drunk]" /> ) Turn the crank to bring the piston up, pushing the rope against the valves. Try it, you'll get good at it quick, and best of all, you'll never lose a valve because of a loss of air etc. Oh yeah, make sure the rockers are off (both valves closed or you might bend a valve)

[ October 28, 2002: Message edited by: BstMech ]</p>
10-28-2002 02:33 PM
BOBCRMAN@aol.com you have to set the piston at bottom dead center not top, if it is at top the piston will travel to the bottom when you turn on the air and startle the sh****t out of you. make sure all the pushrods are out. and give the valve spring retainer a sharp tap at an angle to the valve to loosen the set that it takes after running a few thousand miles. don't let the air pressure fall while you have the spring off. you can buy the overcenter tool to compress the spring at any well stocked parts store they are sold for chevys but with some minor mods can be used on many other motors.
10-28-2002 09:56 AM
Biggarmike There is an adaptor for an air fitting to sparkplug hole. Set cylinder to TDC one at a time and pressurize the cylinder. (be careful) there is a tool available to compress the springs and remove the keepers. The air holds the valves shut so that you can replace the seals and re install the springs and locks. I personally havent used that method in at least 20 years, but many swear by it.
10-28-2002 08:36 AM
ImaPseudonym
351 Cleavland valve seals

I have a '73 Mach I with a 351 Cleavland engine with relatively low miles (51,000). It runs great, but smokes on startup. I've heard that it is possible to change the valve seals without removing the heads. Does anyone have any suggestions on doing this or is it even possible? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.