Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> How hard is it to change valve springs?
User Name
Password
lost password?   |   register now

Thread: How hard is it to change valve springs? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-30-2002 11:24 AM
ScottPuddintane Important Note!!!

Make sure each piston is all the way up before you remove that cylinder's springs (to stop the valve if needed). If a valve slips down into the cylinder you'll have to pull that head!!!!
10-30-2002 05:03 AM
MHenricks You should be able to purchase a hand spring compressor really cheap from the parts store. You'll need it to install the springs you can also use it to remove the springs.
10-29-2002 07:06 PM
Quepas00 I would'nt change the lifters being there already broke in with the cam, and the push rods should be ok also, unless your putting in some kind of monster springs that call for heavier push rods.
10-29-2002 03:31 PM
stfinney Thanks for your help. I changed out my cam a while back, but didn't know I had to change the springs (duh). Would it be a good idea to go ahead and change the lifters again and the pushrods too??
10-29-2002 03:27 PM
Steve karch Its not that hard. If the heads are on the motor, run some compressed air into the cylinder, then with a hamer and a punch with a fairly large diameter or use a socket extension, tap the retainer a couple of times to break the keepers free, then with the spring compressor compress the spring. Use a magnet to remove the keepers and the spring is free, install the new spring, and basicly reverse the procedure except you dont have to hit the retainer. You have to make sure that both valves are closed otherwise the cylinder wont hold any air pressure. If the heads are off you obviously dont need the compressed air.
10-29-2002 03:18 PM
stfinney Yeah, I bought the whole kit with springs, keepers and the retainers.
10-29-2002 03:16 PM
slider in wa yep. You can do it. Need a spring compressor. It is real easy to do. Did you buy new springs?How about new keepers?
Slider in Wa.
10-29-2002 03:13 PM
stfinney
How hard is it to change valve springs?

Can it be done easy enough for a backyard mechanic such as myself?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.