Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> I need help with fender patch panels.
User Name
lost password?   |   register now

Thread: I need help with fender patch panels. Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2005 08:27 PM
Bee4Me Thats one of SEVERAL reasons we opted to get another door for the 59. Way too much work to rebuild that door.
You could make a curvature template from the opposite fender for referencing using c'board and some 24ga sheetmetal as the final temp.
03-28-2005 07:24 PM
antiquecar If you are worried about welding and then unwelding the brace why not drill a hole and use a small self tapping screw to hold it together. You will be geting rid of that piece of metal later so you can't mess it up
03-02-2004 10:16 AM
unstable yeah you're probably right here. instead of keeping everyone guessing, I'll snap some pictures and that will give you a better idea of what I'm talking about.

I'll be sure to move the gasoline away from my welder so you don't see how unsafe my shop is.
03-02-2004 10:14 AM
poncho62 The thing is, that you want to keep that arc the same shape. Sometimes to keep things the same, you have to do stuff twice.............

I'm just guessing here, as I don't know you exact situation.

Can you show pictures of the inner brace?
03-02-2004 10:10 AM
unstable the point I'm trying to get across is that the fender actually wraps around the brace and is tacked at the bottom.

this gives the fender a wee bit of arc to it.

Now what is the best approach for putting this brace back in? I mean, I certainly don't want to reinstall it onto the old portion of the fender? know what I'm saying?

I'll try to get soem pictures tonight.
03-02-2004 10:06 AM
poncho62 I think that you should replace the brace before you cut out the old sheet metal. That way, you can keep everthing in alignment better.

More pics would help, and we would like to see what you are doing.
03-02-2004 10:00 AM
I need help with fender patch panels.

this is a little long, but I could really use your help.

57 Chevy Pickup Truck - 3100 (attached is a picture of the patch panel).

Fender tips are rotted out on both sides, I've got both of the pre-fabbed patches for the fenders. My passenger side also had substantial damage to the brace down near the bottom. I cut it off above the damage and hammered it out...but later decided to purchase a new brace.

I've been using the method described on the Brothers Trucks site to install the patch panels:
-clamp new panel over old panel, ensuring it's perfectly aligned
-cut through both panels.
-Remove clamps and old panel.

This leaves you with a new panel that matches your cut line where you will butt-weld.

-intergrip new panel to existing panel

I've had good success on doing my one door like this. I was scared out of my mind to do the door, but it's turning out ok. I thought the fenders would be a breeze.

Here's the actual problem.
On my drivers side fender, the new patch panel fits perfectly over the top of the original. So I can clamp this down and cut.

BUT on my passenger side, the panel doesn't seem to be fitting on all of the way. I think I've identified why. It seems like since I removed the damaged brace, the fender has flattened out, where it should be curved to lock into the brace at the bottom.

Dilemna. There currently is no brace in place to lock the fender into the correct shape

I COULD install the replacement brace to get the fender locked into place...BUT, I'm going to end up cutting off the bottom of the fender anyhow.

I've PONDERED measuring the replacement panel and also measuring the fender and just manually making the cuts. I'm not really good at measuring or cutting so this scares me. ALSO, I have no idea what to use as a REFERENCE to do my measuring.
The original fender is pretty corroded at the bottom and also whacked out of can I measure from there?

The replacement panel doesn't span the height of the original fender, so where can I reference off of the original fender and apply to the patch panel...

I'm soooo lost. help me please.

if you guys want pictures of what I'm trying to convey, I can take some tonight. thanks for any and all input.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:52 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.