Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Rhodes lifters?
User Name
Password
lost password?   |   register now

Thread: Rhodes lifters? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-12-2004 07:39 AM
1BAD80 Ebelbrock intake site.
http://victorylibrary.com/mopar/edel.htm
03-12-2004 07:13 AM
Roy_67_SS350 Hey,

Thanks for all the replies...

Sounds like Rhodes lifters aren't the anwer.

I think I'm going to swap the cam & lifters for a comp XE 262 or 256 and put on another intake that I have.

Side note: I also have an Edelbrock C3BX intake manifold. It actually looks like it's a little more high-rise than the Performer but not quite as tall as the RPM intake. Anyone with any experience with or knowledge of a C3BX? I'm wondering if it would be a compromise between the other two?

I ran the C3BX on my car for a long time with good results before builing up my engine.

When I get the money for gears and stall then I'll swap the XE268 back in there.

I think the torque-ier combo will be alot more fun to drive around town and will be alot quicker off the line with the gearing and stall that are there now.

Appreciate all the suggestions.

Roy
03-11-2004 07:49 PM
rifraf Yeah,I understand. Ya cant beat a big stall for coming out of the hole quick,nothing I know will replace that with low gears. I have run rhodes a few times,from what your saying you want I think you will be disappointed. they do help a small amount at best,the price of that small amount it a ticky annoying sound,like a solid except it varies. A little distributer tweaking may help you a little,not what ya want,but maybe better.
03-11-2004 05:42 PM
KeithB123 rifraf,...what I`m saying is with my 230/234 camshaft it needs a bigger stall than my 2400 stall .....there is just too much room from hitting the gas peddle to the power range. By the time you get to your power range probably 4000rpms you already got smoked. OR more compression will help this out.

Maybe it is a small cam for alot of hot rodders but it still needs the correct combo.
03-11-2004 05:27 AM
club327 In reply about the 327 crank. Find yourself a cheap 307 as they have the same stroke as the 327's. But I'm no expert in this area and I'm sure we'll get more info from the following posts!
03-10-2004 11:41 PM
KeithB123 gettin off the subject, but don`t you need a 350 crank then you would have a 377?
03-10-2004 11:39 PM
rifraf I don't understand why your power isn't low now. Thats not that big of a cam. I would be looking more at stuff like how my distributer is advancing myself,is the vacuum hose on the right port etc.
03-10-2004 11:38 PM
84_sportcoupe hmm i was planing on a 350 for my camaro. aiming for 13's but guess now i'll take my dads advice and build a 400 destroker 350.
anyone know where i can get a 400 block and a 327 crank?
03-10-2004 11:17 PM
LilSmoke All this changing cams stuff is a little premature I would think. why not just move the cam around first and see what the engine wants instead of what the driver wants. If there is plenty of p/v clearance,advance the cam 4 degrees. Take a comp test and then move it back 2 degrees and move it around till u get the highest comp reading. You dont even have to have the front of the engine together to do this. Just spin the starter,of course once uve got the rockers back on.You only have to have the ones on #1 so it wont take long to do.
03-10-2004 10:44 PM
KeithB123 That`s what I was trying to say...more compression...along with a bigger stall....or smaller cam and Rhodes lifters. The power band is tooo high with that cam. I hear so many say that cam is small but as far as I`m concerned and have experienced that small cam needs alot of compression and stall to make a 3200 lb car move with todays standards.
03-10-2004 10:37 PM
firechicken383 Yes, of the XE274 or XE284, I would use the 274. Personally, I would still go with more compression, unless your wanting to use the cheap grade gas. You have aluminum heads, you could run over 10.1 easy with 93 grade.
03-10-2004 10:32 PM
anglia48 sooooo firechicken ,,,, the X274 would be ur choice with 9.25 cr & alum edelbrock heads ?
03-10-2004 10:18 PM
firechicken383
Quote:
so what's the deal with edelbrock alum heads and the XE274H cam ? you guys aren't the only ones complaining ... would the XE284H cam work better with these heads ? (9.25cr)
Not with that Compression. Personally, I would want at least 10:1 with that.
03-10-2004 10:13 PM
anglia48 so what's the deal with edelbrock alum heads and the XE274H cam ? you guys aren't the only ones complaining ... would the XE284H cam work better with these heads ? (9.25cr)
03-10-2004 07:24 PM
KeithB123 WOW! I just wrote this same post a month or so ago! DV and Luci should remember.....do a search, you should find it.

I agree with you and hear you loud and clear. Everyone says it`s a great combo but......you must have it perfectly tuned and you must have every part of the combo.

This is your post but I must tell you what I have and maybe it`ll help you.

I have the Edelbrock RPM heads, perforemer intake. edelbrock carb 750, 373 rear end and Comp Extreme 274 ( 230/234 @.050 and .490 in and out ). and a 2400 stall. Compression ratio is about 9:7.1.

That combo stinks, the best run I had was a 14.7 ...my 305 ran a 15! I`m sure I could of tweeked it to a 14.2 but I expected low 13`s at worst.

I know what you mean as you need more torque.....my combo would never stop pulling but it just pulled slow and it pulled mostly around 4000 and up.

I had on 1.6 rockers and I went back to 1.5`s...that did help out the low end a little and I also changed the cam timing and that helped out a little. 750 carb and bigger (14 by 3 ) air cleaner also helped a little.

SOOOOOOO...this is what I`m going to do. My engine is all apart now so I`m going to mill the block to bump the compression upto about a 10 : 5 to 1, I may put on a 3000 stall OR go one cam down AND put on the Rhodes lifters. My cash is limited now also so I may go to "Your" cam and put on the rhodes lifters.

I don`t think we would have such a problem if we had roller cams...but I`m learning just like you.

If I were you I would for the time being toss on a .015 head gasket and the lifters. Both cheap. The gasket is weak but it beats a tear down...I`m gonna have it milled cuz it`s already torn down.

I`m, going to everything possible to get more torque, screw the HP...our current combos have plenty of HP but torque moves the car. I`m sure Someone on this board has had the exact same parts as you and I. Recently some one on this board mentioned the exact same thing.....was it you Double V??.....that person mentioned on something to the fact of..street cars should concentrate more on getting more torque.
!!

Let us know what you do ( especially me ) and I will definetly pass it on to what worked for me......it`s frustrating spending $1000 on those heads and have a slow car.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.