Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> 68 power steering
User Name
Password
lost password?   |   register now

Thread: 68 power steering Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-06-2004 08:20 PM
poncho62 That's a nice way of saying....Hit it with a hammer................
04-06-2004 08:10 PM
burner
massaging headers

What's the best way to massage the header pipe to fit around the steering gear box?
04-06-2004 06:49 PM
troy-curt I've been building camaros since day one and I don't know of any other stock type sector that fits. Have had some guys tell me they used the later model ones, but had some kind of ratio problems.

Any header is very close to the sector. some will fit and some will not, most will not. I gently massage the tube to get about a 1/4 inch clearance. I have even bolted them to another engine in the floor and sprung them enough to get some clearance. Good Luck

Troy

__________________
If you don't make mistakes. your not doing anything.

69 ss rs full custom camaro 98 ISCA grandchampion
69 ss rs bb camaro wifes driver
66 Elcamino 350/all dz parts,ac,windows,loaded,my driver
69 ss chevelle bb conv.fresh frame off
26 T sedan street rod
04-06-2004 05:00 PM
burner
68 power steering

Thanks for the suggestion, but I'm still wondering about the gear box since I had the same problem with Flowtech Afterburner headers. Those just barely fit, but still rubbed. They were 1 1/2 inches, my Hedman's are 1 5/8 inches. I opted for the Hedman's instead of Hooker's because of the setup with the Fastburn heads, they were the only one's guaranteed to fit. Plus I'm not sure if Jet Hot will take them back since they are scratched up from the gear box. I guess I'll just keep trying to figure it out!
04-06-2004 09:33 AM
11echo Earl ...I'm not going to be much help to you here, but I think your looking at this problem all wrong. The power steering is not the problem, it's your headers! I have a 69 vette and had a set of Hedman headers also. The headers rubbed on the steering box! Until I finally changed them out with another set of headers (Hooker's) ...the problem went away! I'm not sure you can return your headers, but I would try. Don't end up trying to make "poor quality" work! My $0.02, Good Luck! ...Mark
04-03-2004 05:44 PM
burner
68 power steering

I have a 1968 Camaro, originally a standard coupe with a
six cylinder and a power glide. The VIN# is 123378L303966. I
now have a 383 stroker with a Turbo 400. I have always had
clearance problems with my Flowtech Afterburner long tube
headers(1 1/2 inch primaries, 3 inch collectors) rubbing against
the stock power steering gear box. The number 3 tube would rub
and create an awful loud vibration at low rpm but would usually
go away once I'm up to speed.
I recently upgraded my cast iron SR Torquer heads to the GM
Aluminum Fast Burn heads. Because of this upgrade, I also had
to change my headers. I ordered a set of Hedman Shorty headers
from Jet Hot with 1 5/8 inch primaries and 3 inch collectors.
Now I can't even move the header into place to bolt it in
because the number 3 tube hits the power steering box even worse
than before.
Is there a smaller power steering gear box that I could swap
over to that would give me the room I need to bolt the header in
place? I thought I read somewhere about either an aftermarket
gear box for a Nova that would work, or a third or fourth
generation gear box that would be smaller. If not, does that
mean I'll have to convert to manual steering, and if so, would
that fix my clearance problem?
I know I've consistently read about guys with headers even
bigger than mine that have power steering and it looks like they
have plenty of room. Any help you can give would be great!

Thanks!
Earl Brunson
Pensacola, FL
ebrunson@ureach.com

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.