Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> what plastic should I use
User Name
Password
lost password?   |   register now

Thread: what plastic should I use Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-07-2002 04:40 AM
tlambert If its the type with just a round hole (70s ford style?) with no reinforcement what you did should be fine. Flangeing it was a good idea so it will add more strength and after the weld has been ground you won't end up with a weak area around the weld joint.
Oh yeh those directions do come in handy don't they.
11-06-2002 08:51 PM
crazy larry so let me get this clear..... I should cut a section around the filler neck (incab tank relocated to under bed) and weld in a patch? what i did was cut a circle close to fit, and flanged it to fit somewhat flush from the inside of the cab, not to much of a gap, was hoping filler would take care of it but i dont want to be in the middle of my paint job and see the patch....... please expound on this.......
of yeah,,,,,when all else fails, read the directions <img src="graemlins/crash.gif" border="0" alt="[crash]" />
11-06-2002 03:34 PM
tlambert Crazy L, by the way we use Evercoat brand fillers and polyester fillers for my class, they dry good and sand pretty easy. Sanding with 40-80 grit is not bad at all. Don't forget to read the directions on the label <img src="graemlins/mwink.gif" border="0" alt="[mwink]" /> it does seem to help with questions that may arise during use.
11-06-2002 03:23 PM
tlambert Crazy L you spoke of filling a gas hole in, I've seen this done by welding a piece of sheetmetal in place(door handles) without cutting the surrounding area out. Each time I've seen this done they show up later in the paint job. The best way to fill an area like a gas opening or door handle is to cut the area out and weld another piece into its place. When this was done it didn't show. FYI
11-05-2002 09:12 PM
Halloweenking Happy to help

HK
11-05-2002 09:04 PM
crazy larry I 'ppreciate it, will keep you posted. <img src="graemlins/crash.gif" border="0" alt="[crash]" /> <img src="graemlins/drunk.gif" border="0" alt="[drunk]" /> :p
11-05-2002 09:02 PM
Halloweenking I use 'glass filler for big jobs that I want to stay for awhile with structural integrity, then use a thin coat of plastic filler to smooth out the 'glass, because everyone knows plastic smooths way better than 'glass filler. Just for small jobs for filling in or smoothing just use plastic, no need to use 'glass. I only use glass when I'm doing a $600+ cost in materials type job.

HK
11-05-2002 09:00 PM
crazy larry its my daily (gonna be) driver, though I don't wanna 1/2 arse it
11-05-2002 08:58 PM
Halloweenking Its not a bad product at all, just a real beetch to work with like you said, if you think thats a real beetch to sand try metal2metal after its cured you need a frikin arm of steel to do it (why I rarely use it). Try Evercoats 'glass filler, its easier to work with. I try to use as little filler as posible unless its one of those cheap rush for fun jobs lust to make your day-to-dayer look good without alot of work.

HK
11-05-2002 08:58 PM
crazy larry course he's DEAD, only gone home. should I use a fiberglass filler or stick with plastic. area to be done is'nt to deformed. also, what is better for larger surfaces, say for instance, a gas filler hole. sheetmetaled in, ground as smooth as I ccan get, just to make it purty
11-05-2002 08:44 PM
BstMech Wadd'ya think of mar-glass, other than it being a beetch to sand?
11-05-2002 08:42 PM
Halloweenking He's dead havn't ya heard :p

HK
11-05-2002 08:29 PM
crazy larry Garcia
11-05-2002 08:23 PM
Halloweenking I myself use Evercoat brand filler, from thier lightweight plastic to fiberglass or even the ocasional metal 2 metal. Somtimes I use filler by 3M, but its not reddily available around here. I myself try to stay away from anything made by Bondo, but thats just me. I like Evercoat its a good filler and its redily available here and not to terribly exspensive.

HK
11-05-2002 08:14 PM
crazy larry Hey Halloween King, what do you use?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.