Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Broken 400 SBC flexplate with a 350 block...
User Name
Password
lost password?   |   register now

Thread: Broken 400 SBC flexplate with a 350 block... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-20-2004 11:23 AM
realsquash It appears that it has the correct harmonic balancer for a 350. I know from driving the truck at about 40 mph was a real event, tons of vibes. The rear driveshaft was completely shot, I'm suprised it survived the trip home, but I suspect that was where the vibrations came from. The engine sounds great and had good power, so I don't think the bearings have toasted... Of course none of the gauges are hooked up either so who knows if it even has oil pressure.

I know for a fact this truck was driven quite a bit, I even rode around in it before I owned it. I'm pretty sure it's a 350 with the wrong flexplate now.

Thanks for everyone's input, it's greatly appreciated.

Andy
04-20-2004 09:25 AM
coldknock There aren't any differences visible from the outside. Drop the pan and have a look at the cranks casting number. It's possible that a 400 damper and flexplate were used on a 350. It'd shake like he-double toothpicks when it ran. I mean it would vibrate so bad that you'd know something was very, very wrong. It would take about 5-10 min. of running to kill the bearings and the oil pressure would drop quickly.

Larry
04-19-2004 10:18 PM
jimfulco What is the shape of the rear flange of the 400 crank. The imprint on the flexplate might be a clue.
04-19-2004 10:58 AM
Jmark You indeed do have a 400 flywheel in that pic. The 350 balancer will be smooth all the way around, inside and outside surfaces.
The 400 balancer will have a big recess in one area, that is the "light" side of the balancer.

Mark
04-19-2004 10:56 AM
DoubleVision if it`s a 383, then on the harmonic balancer there will be a counter weight cut out, in other words it won`t be completely round all the way around the outer circumference, but that don`t mean it`s a 383, since all balancers interchange, it would go on a 350 but would be out of balance with bearing damage resulting. one way to be sure is to check the rear mounting flange of the crank, if there`s a dowel pin in the flange, it`s a 400 shaft.
04-19-2004 10:23 AM
realsquash
Broken 400 SBC flexplate with a 350 block...

I have a dilemma here. I have this old chevy truck that I bought and it has a TON of redneck crap that I'm basically reversing. The truck had a knocking sound and I figured it was the flexplate. Well it was indeed cracked, so I removed it. It looks like a 400 flexplate to me because it has a counterweight. I've attached a picture of it.

I know the engine has been rebuilt, and the casting number (3970010) says it's either a 327 or a 350. I'm concerened/hopeful that this is actually a 383 (400 crank in a 350 block), so I need to figure that out so I can get the right flexplate on it!

I've heard there are externally visible differences on a 400 harmonic damper? Any ideas? Help me figure out what the hey this thing is!

Thanks,
Andy


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.