Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Base Timing - Advance timing
User Name
Password
lost password?   |   register now

Thread: Base Timing - Advance timing Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-11-2004 07:45 AM
Frisco
Quote:
Originally posted by chevelle67
I guess that info would help a little. The engine is 10:1 compression the cam is a 230 duration with a 480 lift and it is running on pump gas 92 octane
A good starting point would be 10-12 degrees initial and 34-36 Total mechanical (initial plus mechanical) all in around 2500-3000 RPM. Set this with the vacuum advance disconnected and plugged. Re-connect the vacuum advance after you have set the timing.

Don't worry about what the timing shows with the vacuum advance hooked back up as it will not function at WOT. You may wish to limit how much advance the vacuum pot gives you by using an adjustable one. Try it first to see.

If you get pinging when in high gear going up a slight hill at a moderate speed; back off the timing 2 degrees and re-test until no pinging occurs.

As to running the engine without the vacuum advance; Yes you can but for street application I would not. The vacuum advance is designed to improve the overall driveability and gas mileage. For a race only application it is not neccesary because you would be at WOT and there is '0' vacuum at that time and therefore the vacuum advance will not function.
05-11-2004 07:33 AM
chevelle67 I guess that info would help a little. The engine is 10:1 compression the cam is a 230 duration with a 480 lift and it is running on pump gas 92 octane
05-10-2004 10:44 AM
Tmod Really hard to suggest something when no info is provided on cam, compression ratio, fuel octane and what the intended use is.

These all play a important roll in the choice of the optimum advance curve and total timing.
05-10-2004 10:17 AM
chevelle67
Base Timing - Advance timing

All right another question for you guys, since you did very well on the last one. I got a 327 SBC and I have the base timing set for
4 degrees. My question is 2 part what should the advanced timing be? Can I run the engine without vacuum advance? I was told that I should be around 34 advance without the vacuum advance and install the vacuum and if it goes up to 45-50 degrees don't run it. What do you guys think

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.