Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Four hole carb spacers
User Name
Password
lost password?   |   register now

Thread: Four hole carb spacers Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-29-2004 10:21 AM
Tmod Most spacers that are available are 1" thick, You can get other thicknesses but the availability is not as abundant as the 1".

Some people don't like the software Dyno program but I have several different programs as such and one takes into account the spacer height and I found that a 1" gave me the best powerband down low then either a 3/4" or a 1 1/4" spacer.

I also build my own spacers as most of the available spacers are for carbs with a bore size of 1 11/16" and if you have a spread bore the bores of the spacer don't match with the bores of the carb. The primary spacer bores will be bigger then the bore of the primary throttle plate.
05-29-2004 07:57 AM
stepside454 if your staying within 5000 RPMS Id recomend a smaller carb than a 650, or...a Q-jet, even though a Qjet is actually more CFM than 650, because of its spread bore design, they make greal loe end as well as top end.
If staying with aftermarket square flange for a 350 that never revs past 5000 RPMs Id use a 570 Holley Street Avenger. There are going to be a few in here that call me crazy... but within that kind of RPM thats all that motor needs & it will respond well, infact it would even better with a 4 hole spacer.
Sune... yes an open spacer has the oppisite effect, makes the engine think it has a lil more carb. John
05-29-2004 07:49 AM
sune
Quote:
Originally posted by stepside454
if your wanting more low end yes, a 4-hole. How thick? cant say itll very from 1 engine to another. basically the way it works is, it decreaseses the plenum volume boosting the signal, so the engine reacts like it has a smaller carb. smaller carbs generally give more low end & thoratle response. I asked you before & you never answered.... what max RPM do you run this motor ?. John
Sorry to instrude with my own questions....

I have been wondering if you can go the opposite way, and make the carb seem bigger to the engine with a open spacer..?

Sune
05-29-2004 07:48 AM
stinky jinx 4500............sorry about not replying. I am new to how this forum works.
05-29-2004 07:44 AM
stepside454 if your wanting more low end yes, a 4-hole. How thick? cant say itll very from 1 engine to another. basically the way it works is, it decreaseses the plenum volume boosting the signal, so the engine reacts like it has a smaller carb. smaller carbs generally give more low end & thoratle response. I asked you before & you never answered.... what max RPM do you run this motor ?. John
05-29-2004 06:54 AM
stinky jinx
Four hole carb spacers

I am sorry that I am slow to understand carburation but.............are you all saying that in most situations a 4 hole spacer will give you more low end power ? If so does it matter what thickness it is ? Let me put this another way for anyone new to my questions.........for a 350 chevy motor with a mild cam, a duel plane air gap intake manifold, shorty headers, 350 B&M trans, 343 posi and a 650 single pump carb, should I put a spacer on, and should it be a 4 hole if I am wanting more low end power?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.