Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Electric Fuel Pump Installation
User Name
Password
lost password?   |   register now

Thread: Electric Fuel Pump Installation Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-30-2004 03:43 PM
club327 .
05-29-2004 09:39 PM
club327 Just remember a relay is a remote heavy duty switch that can be mounted close to the load (pump) and triggered from a light duty switch (and wires) that's close to the driver. Inside the relay is an electrical coil that becomes magnetically charged when a current is fed through its windings. Feeding battery 12+ volts and earth to terminals 85 and 86, in any order, will cause the coil to charge with magnetism. This pulls the relay internal contacts together forming a circuit that could carry roughly 30amps of current - these contacts are terminals 30 and 87 - again in any order.
This is how I would do a basic wire up with the limited information you've given us. Connect a light gage wire to terminal C from your push button switch to terminal 85 on the relay. Next feed a wire from terminal 86 and to earth - again a light duty wire will suffice. This will now activate the relay on command and you should hear it click on and off as you trigger your push button switch.
Now the feed for the pump itself. Here we use heavy gage wires which must be fused - refer your pump's requirements. But something in the order of 25amps would be close. So connect a fused power supply wire to terminal 30 and the fuel pump + terminal to 87. Make sure you've got a good earth wire and connections for the pump negative side.
Just remember, electric fuel pumps are dangerous in a collision - eg, engine's off, ignition's on, fuel line's ruptured and fuel's pumping onto the hot exhaust. Give me more info. Is this pump used for permanent fuel supply or is it an auxilary fuel pump? I can help you set it up to protect you and your occupants in an accident. Rob.
05-17-2004 03:04 PM
riesman20
Electric Fuel Pump Installation

This is what I have so far. The ignition to the NO on the Press Switch then the NC to the Positive side of the battery then the C on the press switch to the relay but What point ? there is 30, 85, 86, 87. then from the relay to the battery(pos?), then from the relay to the fuel pump(pos?) than from the fuel pump to battery(neg?) is this correct?
ps. I have a fuse between the relay and the battery and between the ignition and the press switch.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.