Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> good and bad
User Name
lost password?   |   register now

Thread: good and bad Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-06-2004 05:32 PM
jrm123180 the intention with this job was only temp. its not a daily driver. I use it for fun and to do some odd jobs and plow in the winter. I do have another engine that i want to rebuild. Thats down the road though, since i want to build it up and money is tight with a new baby at the moment. thanks for your help.

06-06-2004 04:51 PM
LanceM Ok mechanical gauge so it is probably reading true over tempature.

If you want to go cheap I'd do the oil pump and while you have the pan off pull at least one of the main caps just to see what kind of shape the mains are in. With 150K showing you should have gone with the whole works, guess it depends on if you just want it to last a little while longer or another 150K.

For future note, for all the trouble you have to go to pull the pan in most vehicals it's cheap insurance to replace the oil pump if you have the pan off...

As for changing the bearings, it probably could be done, maybe, in the truck but it would for sure be a lot easier with the engine out!
06-06-2004 03:45 PM
jrm123180 my gauge is mechanical.....

could it be that i bent my oil pump and its too close to the bottom of the pan?

before I did this job, i would loose oil pressure but that went with the oil. as soon as I added more oil, the pressure would come back up...but not to where it should be. The motor has 150k on it and the pump is original to my knowledge.

Are the bearings something that can be done with this engine in the truck? should i just replace my pump and see if that does anything?

thanks for eveyones help
06-06-2004 03:12 PM
gpeak If your rings went then your bearings aren't too far behind. Always do your bearings when doing rings or vise versa.
06-06-2004 02:38 PM
LanceM Not the pump, the oil pressure gauge, is it mechanical or electric?
06-06-2004 01:47 PM
knock knock

Sorry, but it sounds bad to me. No noise before the work sounds like a loose rod at worst. Did you change the rod bearing , tight pistons with loose bearing cause knocking. Bad oil pressure after warm up sounds bad cam bearing.
06-06-2004 01:38 PM
jrm123180 it is a mechanical pump. I did not check the main's while I had it apart. I didn't even remove the motor from the truck. Are the main bearings someting that I can replace fairly easily like by just removing oil pan? Also, i did not replace the oil pump.

also....when i remove the rocker arm covers, I do get our coming out of there if thats any help
06-06-2004 01:22 PM
LanceM While you had it apart did you put in a new oil pump? Typicaly low oil pressure and a "wacking" noise means bearing problems, excessive clearance on the mains will give you low oil pressure.

Other questions:

Mechanical or electric gauge? If electric maybe a bad sending unit.

You said that it did this before the ring change, did you check the mains while you had it apart?
06-06-2004 01:09 PM
good and bad

Ok, the good.....after many posts and much help, I have finally started my pickup. the timing is set, and the carb is almost tuned.

The bad....after running it for a bit, I am getting no oil pressure (which i had when i had first started it), and I am getting a wacking noise from somewhere in the motor. I can not figure out what it is. I think I may have an idea but I"m not sure. All the valves have been adjusted so I know they are not chattering.

A bit of info:
its a 1979 chevy K10
holly 650cfm carb

I just pulled the engine apart to put in new rings in all the way around.

Before i did this job, i would loose oil pressure after running the truck for a bit; along with that came a loss of oil as well. The oil dip stick seems to be reading at full so i know I have plenty of oil in there. When I rev the engine the oil pressure goes up and then drops to nothing.

Any help please, i can use it. thanks once again.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 06:41 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.