Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> looking for a good after market 400 sbc block
User Name
Password
lost password?   |   register now

Thread: looking for a good after market 400 sbc block Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-13-2004 09:54 AM
406 ss monte whats the casting number of the high nickel block? i think it's 511, but not sure. their two bolt mains as well i believe. please correct me if i'm wrong.

i can get a dart aluminum block, all 5 mains are 4 bolt's. the oil pan rails are spread .800", & it takes big block cam journals, & i would have to run a remote oil filter. i can get it for $ 1,000 bucks. the only thing is, i've been told a oil pan to wet sump the block will cost $600 bucks. plus i can't find one that will fit my 85 ss monte carlo, in fact i haven't found any yet.


what to do, what to do.
06-12-2004 08:37 PM
trees I know a guy building circle track motors putting out 680HP and they are holding up good. He uses the high nickel 2 bolt main blocks and splays the other two bolts (studs) I have not heard him addressing any cracked webbing, but the high rpm circle track motor may not be experiencing as high a stress as the sprayed drag motor. I would get a few more race engine builders opinion before blowing of your block.

Trees
06-12-2004 02:43 PM
68c10owner my friend was running a 410 sbc with a stock 2 bolt block with a scat lower end with nos and it was a low 9 second car. i don`t know what shot he was running but it only ran low 11`s on the motor alone so i`m guessing he had more than a 250 shot. he raced it for a long time with no problems at all. a 2 bolt with splayed main caps should be fine. i`m not a big fan a nos but i think your crank and rods would go before the main webbing. i would not use a stock 4 bolt 400 block though. i would check with another shop for a second opinion. i`m not saying your guy is wrong or doesn`t know what he`s talking about, i`m just saying i`ve seen it done and the motor was ran hard.
06-12-2004 02:39 PM
DoubleVision we sprayed 350 horses to a 400 small block with a stock bottom end for a whole season and didn`t have any bottom end problems. set your bottom end up with studs and I doubt you`ll have any problems out of it, providing your Nitrous is set up properly and your running forged pistons and good rods. keep control over the RPM`s also. If I still didn`t feel safe in your case I would just get a "progressive" nitrous system to help soften the blow.
06-12-2004 02:31 PM
406 ss monte
looking for a good after market 400 sbc block

i went to the machine shop yesterday to get my bottom end balanced, & before i left he told me that sence i'm going to shoot a 250 shot of nitrous on it, it wouldn't last long. he said the main webbing would come out of it. so i'm looking for a good affordable after market block. what i want is every thing in it's stock location, & the big 400 mains.

the dart lil m block would be great if i could afford it, so would a motown, but i don't have $2,000 to put in a block. i even asked about a 400 2 bolt main with splayed main caps, he said it would still bust out the webbing, just take it longer to do it. if i would have known this, i would have built a 383, just for the fact that the 350 block is stronger.

by the way, this is for a street car. i'm pushing a little over 500 hp out of it, & with the n2o it would be 700-775 hp.

please tell me where i can get a affordable block. the bore is 4.155"

thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.