Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> "problems with a crate motor 350/330hp??"
User Name
lost password?   |   register now

Thread: "problems with a crate motor 350/330hp??" Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2003 04:51 AM
302 Z28 I am assuming the crate engine was new when you bought it, so that rules out any rebuild problem. There have been some reported problems with excessive cylinder wall clearances on certain early GM Performance Parts crate engines. Since yours was purchased in 00, it may be one of the affected ones, Whether or not you can get the dealer you purchased it from to admit it, that is another story. Your description of the noise sounds like a piston slap due to excessive clearance IMO.

09-18-2003 10:38 PM
Vern Bradford I agree with Bob that the problem is in the piston area. You might run a compression test on the engine or a leak down test to see what the problem is. It could even be a broken ring. At any rate it is best to pull it a part now and possibly save some money in the long run. Good Luck,
09-17-2003 08:34 PM

Check the easy stuff first. Is the knock coming from the top or bottom?

Sounds like you could have a lifter out of adjustment or sticking. I had a sticky lifter on my V6. I got tired of hearing it so one day I just floored the darned thing. Problem
12-12-2002 07:12 AM
chevelle327 I had a simialr problem with my car, but mine was a popping out the exhaust. I later found out that one of my plugs had a crack. I dont know if that mihgt be of help to you
12-11-2002 06:18 PM sounds like maybe one of the pistons galled a skirt, a common problem on rebuilds that have been in storage for years, the oil that the engine was assembled with has migrated somewhere else leaving a dry cylinder dry piston skirt and when you fire it the skirt trys to weld itself to the wall because of no lube. this lets the piston rock at idle and make noise. also check to see if the piston is clearing the crank counterweight and the crank is clearing the windage or oil pan baffle.
12-11-2002 06:07 PM
"problems with a crate motor 350/330hp??"

i have a 350/330hp crate motor vortec heads with the GM vortec aluminum intake w/egr, counter balanced flex plate, correct harmonic balancer per catalog, new distributor, fuel pump, knock sensor, temp sensor, oil sending unit, and all other "under hood parts & accessorise are all new including OE GM headers all the way back exhaust system w/magnaflow cats 3" and flowmaster 40'serise muuflers...
********* problem is there is a very *********
pronouced knock from the mid to lower part of eng on passenger side between cyl#4-6!!!! anyone else having or had this problem if so what was diagnoises?? any sugestions as the motor was the on floor display modle at my local GM dealer when purchesed in 04/00 and is so claimed by the dealer to be "out of warranty period" motor has only been ran poss 1hr idle to cruse rpm's...
the knock seems to go away just as the rpms come up and stays gone untill idle returns to normal. eng sounds strong and sees to run good. the eng was recently started after long and costly instalation period as i did not cut corners for my on going building of my truck.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:18 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.