Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> what size carb for 400 sbc
User Name
Password
lost password?   |   register now

Thread: what size carb for 400 sbc Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-27-2004 09:16 AM
Canadian Charlie I suggest using a Holley 750 double pumper on your 400. I go 1 on my 350 and its great
07-07-2004 04:35 PM
stepside454 Cub, its really tough to say without knowing more. You said its a stroker...so we dont know what the actual dispacement is, do you know what kind of RPM you plan to rev it to ? knowing more info about the cam, compression ratio, & what the actual displacement is would help a bunch. without that info, noway to recomend anything. John
07-07-2004 04:18 PM
cub lluciano77. thanks for the reply. It is a 400 sbc. I just do not what is in the motor yet,after I get quarter panels put in(body man keeps putting me off)I'm going to pull motor and rebuild front end and dress up motor. At that point I find out what is in the motor. The guy I bought it from said he had over $4000 in motor. He could not tell me what was in the motor. I got the car cheap enough it did not matter.
07-07-2004 02:17 AM
Croz I merged jajeff22's thread that he started by mistake as a reply into this thread. I believe this is where he wanted it. Let me know if this is the wrong place.
07-07-2004 01:47 AM
lluciano77 With your gearing your 400 will do just fine with a 750 DP. A 750 vac. carb would probably get better mileage, but your RPMs will come up a lot faster with the DP. Which is more important to you?

An 800 DP would even work well too if you don't mind losing a little throttle response. It might make the most overall power.


You say that your engine is supposed to be a stroker motor. You can't stroke a SBC to get 400 cubes. Only 400 or aftermarket blocks will make it to 400 cubes. Read the casting numbers at the back of the block and then look them up online.
07-06-2004 12:53 PM
fried_guy For the street I'd stick with a holley 750 vacuum secondary. There's tons of tuning/tricks you can do to those carbs, or you can leave it pretty much alone if it runs good.
07-05-2004 08:53 PM
jajeff22
carb size

hi cub, i've got a 400 destoked to a 377 . and i'm running a 670 steet avenger. i think i have it tuned preety good and it runs like crazy.just a thought jeff

sorry cub i hit new message , not post reply my bad . jeff
07-05-2004 04:55 PM
cub
what size carb for 400 sbc

I decided to replace the carb on my Camaro. It has a 750 on it now. I took it apart to rebuild it and found that someone had broke some parts. I'm still going to work it to get it right just to learn but I think it needs to be replaced. What should I put back on it 650 or 750 ? It is 400 sbc with 488 lift cam. (supposed to be stroker motor) very high compression 215 psi. turbo 350 trans and 373 gear. What is going to be the best car just to play with on the street? ? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:39 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.