Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Where to buy Suspension Bushings for Custom Suspension?
User Name
lost password?   |   register now

Thread: Where to buy Suspension Bushings for Custom Suspension? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-23-2004 03:55 PM
bigfred1958 Just a little update.
I went out to my car at lunch and looked carefully at the bushings I bought today.
they are energy suspension for '73-79 Ford truck leaf springs. The nice thing about these is that they are quite long ~2.75" which gives lots of room to adjust the width of my trailing arm end, if needed.
The tubing they will be inserted into is 1.5" DOM with a 3/16" wall. The tubing ID is 1-5/8. Perfect for the bushings.
The bushings fit into the tubing well without the inner sleeve. With the inner sleeve inserted the bushings are a *perfect* fit for the tubing. Very tight.
What I'm doing is drilling a 1-1/5" hole in a piece of 2x2 1/4" wall square tubing. I'lll inset a piece of round tubing into the hole and weld it to the Square tubing. The bushings are inserted in the round tubing. Over all, my lower trailing arms have cost a grand total of $55 including a 1-1/2" hole saw.

A little plug for I payed $40 for a set of 8 bushings and 4 sleeves (enough to do 4 trailing arm ends). The D.O.M. tubing cost me about $6 for the amount I'm going to need. Suicidedoors sells the bushings w/ the tubing pre-cut for $9/end. A bit cheaper than it is costing me to make them myself... However, I had to get a different size sleeve than suicidedoors offers. Of course, I have the satisfaction of saying that I built my own trailing arms... not sure what that's worth.
08-23-2004 10:58 AM
bigfred1958 Ok,
I'm slowly getting the trailing arms together.
The thing that has been a little difficult with this is that I'm limited to bushings with a 5/8" sleeve because the rear shock mounts are built into the trailing arm bolt, which is 5/8" . If I wasn't limited by this, I would have just ordered the bushings & ends from

After some trial and error with generic leaf-spring bushings, I went back to the spring shop where I purchased the bushings and got some "energy suspension" polyurathane bushings.

The new bushings are for a '73-7? Ford.
I'm using 1.5" OD (1.25" ID) D.O.M. Tubing and pushing the bushing into the tubing.

Here's my latest concern....
The new bushings are not the tightest fit. Not loose, but not a tough press fit. However, when I push in the inner sleeve, the bushings really tighten up on the tubing. For those of you that have done this before, does this sound like it will work?
Thanks again
08-21-2004 01:02 AM
WICKEDFAB if you buy some leaf spring bushings for a 90 wrangler they will work with 1.25 id tubing and the others 1.5 id 1.5 120 wall and 1.75 120 wall....if ya need small chunks of tubing i can hook ya up....i can also get ya the bushings...
08-20-2004 04:49 PM
bigfred1958 Thanks Guys!
08-20-2004 12:40 PM If you need simple push in Three piece bushings MAS in Minesota has 5/8 and 3/4" ends. The same as used in street rod, four bar systems.
08-20-2004 10:44 AM
Rich_Long I'm goin through that right now with a set of under rider traction bars I'm making.

I went here:

No size there for me, so I emailed them , no reply. BUT, through I hooked up with Wes at
who is a Quikor dealer, and he's helping me out.
He's also working on a rear sway bar for my project Mustang.
08-20-2004 09:23 AM
Where to buy Suspension Bushings for Custom Suspension?

Now that I've decided to build my own trailing arms for my car,

I'm looking for a good local joint that can sell me bushings.

I'd prefer not to use the hard to work with press in kind.

I guess what I'm wondering is if anyone has built their own trailing arms and what did they use as the source of their bushings?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 12:00 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.