Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Car missing while on Dyno?
User Name
Password
lost password?   |   register now

Thread: Car missing while on Dyno? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-07-2004 10:17 AM
FBody Thanks Guys for all your responses.

I'm not sure how I will be able to confirm if I fix anaything, as it's not making it while on the raod (even going up a hill).

Thanks,
Daniel.
09-03-2004 01:41 PM
TurboS10 I am going to vote ignition. I had the same problem at the track with my 57 until I put a hot coil and MSD6 on it. Under hard load the stock coil is just not going to cut it in a performance application. The reduced plug gap will also help out if it is ignition.

Chris
09-03-2004 12:37 PM
Litdave "Car missing while on Dyno"

I hope you find it!!!


....


couldn't resist
09-03-2004 09:51 AM
4 Jaw Chuck Running a reduced gap at the plug will help, try .035". Dyno runs load the engine beyond that encountered under driving conditions and for longer periods of time.
09-03-2004 08:10 AM
FBody Thanks for your responses guys,

I will try new plugs on the weekend. It's the only thing that I haven't changed and I really don't how old they are, as they were on the car when I bought it two years ago.

If this doesn't fix it, I will move on to the wires and distributor, although I would like to keep the stock ones.

Thanks,
Daniel.
09-02-2004 08:18 PM
NAIRB If there is any weakness in your existing ignition system, it's gonna show up under extreme load conditions. Happens on the street, the track and the dyno. I always find a big hill to accelerate a customer's car up if I suspect faulty plug wires, plugs, etc.

Just remember that your ignition system is working exceptionally hard to fire a spark under these extreme cylinder pressures as the engine works hard against a dyno. Modern cars do have superior designs in terms of ignition energy, so the old school Chevys need all the help they can get. As mentioned by Doc, try to eliminate spark scatter with a wide cap, use high quality plug wires and fresh plugs, and make sure you have enough juice to throw the gap for the application you are running. Electricity will follow the path of least resistance, so as it encounters more in the combustion chamber, everything else has to be sealed up tight (so to speak).
09-02-2004 02:23 PM
docvette
Miss

[size=3] Doc here

Most likely, what is causing the High RPM miss is when you converted the points distributer over to a high Energy conversion,

The Cap is not spaced Wide enough to Resist Cross fires across the plug pick ups, This is one reason why HEI Caps are so large.

Go to a Good Spiral Core 8 MM or higher wire too...And Wider Plug gaps.

You may Want to Consider, if you have the room, Getting a GM HEI Distributor ET&AL...They are good to about 7000 RPM.

Hope IT Helps!

Doc
[/size]
09-02-2004 02:08 PM
FBody Yes, I did supply the Crane XR-i module with a switched 12 Volts, while the Coil power is still supplied through the resistor wire.

Thanks,
Daniel.
09-02-2004 12:33 PM
USA1 When you changed out the points to electronic, did you run a new power wire to the distributer? If not, you are running at around 9 volts to the coil when you should be running 12. Just a thought. That would make it miss under a load.
09-02-2004 08:43 AM
FBody Thanks for your response snkbyt,

I got the Camaro 2 years ago, last year I changed the following:

o AC Delco Distributor Cap
o AC Deco Spark Plug wires
o Crane XR-i Electronic Ignition Module (replaces the points)

But I never changed the Sparkplugs, since they all looked Ok.

Last year, I purchased a Proform Adjustable Shift Light and it never worked on my car, before and after the above changes. The light is always flickering. I know that the shift light works as I tried it on a friend's car.

I will try changing the plugs and try my Proform shift light again, maybe it will work.

Thanks Again,
Daniel.
09-02-2004 03:31 AM
snkbyt FBody, on a Dyno its under load. So that is normally a spark problem or lean mixture. It would miss on any Dyno. Spark plugs problem, wires, possible timing.(too advanced at rpm). You should get thje same problem pulling a steep hill/ So you wouldn't have to pay Dyno fees.
09-01-2004 09:22 AM
FBody
Car missing while on Dyno?

Hi,

A local tuning shop had a car cruise last weekend and they were offering dyno sessions/runs for $50.

I decided to put my 69 350 Camaro on their Dyno (Mustang Dyno) to see what was my output at the rear wheels.

To my big surprise and disappointment, my car started to in the mid - 4K RPMs. The Dyno curves (HP & Torque) shows starting to go down around 4,000 RPM while the curves would be expected to be still climbing until it start reaching the 5,000 RPMs.

While speaking with other friends of mine that went the shop earlier that same day, they told me that most of the cars that they saw on the Dyno were also missing at high RPM.

The questions I have are:

1) What would cause my car to be missing on the Dyno.

2) Will my car be missing on all Dynos.

Thanks,
Daniel.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.