Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Suffering Flames
User Name
Password
lost password?   |   register now

Thread: Suffering Flames Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-08-2002 06:46 AM
DDent Obviously you have to get a design down on the body. I use a white or black china marker to sketch it out. then when I'm happy with the layout, I tape it with 3M fine line tape. I like the blue stuff. Filling in between is time consuming and tedious. I use 2 inch. After you tape it all off and mask back to prevent over spray, wash it down really good with wax and grease remover. Scuff all tape eges with great care. Make sure you get rid of all shiny surfaces. If the fine line comes up remask it. Wet or dry sand the rest with 400 or 500 depending on the kind of paint you're using. After you lay the paint down and depending on how elaborate the flame scheme is you pull the tape. This is the crutial step. You can pull the paint right off if you're not carefull. Get all the fill masking off first then work the fine line. When we worked with lacquer we sometimes pulled the fine line tape immediately before the paint was dry. Today you have mostly enamel and your better off letting it dry or harden first. Pull your fine line off at a 30 degree angle into the fresh paint, so that it cuts a clean edge. That's one of the tricks so you don't pull off your new flames. I hope this is helpful.
03-07-2002 04:22 AM
waltmail You might try buying or borrowing the current issue of Car Craft magazine. A complete detailed article on the art of painting flames.
03-07-2002 03:36 AM
early-hemi For help with your flames try www.customflamepainting.com
03-06-2002 02:33 PM
stoke46 You might want to get a back issue of Rod And Custom. In the May 2001 issue it has a whole issue on painting techniques The article on flame painting is very informative covers from layout to finishing
03-06-2002 04:45 AM
57Chevyman Also if you are wanting to do it yourself a pin stripe on the edge of the flames looks sharp. Before you start to shoot the flames paint the edges the color you want the pin stripe to be and fine line tape over it folowing the tape edge on the car then shoot the rest.
03-05-2002 07:29 PM
'66Biscayne If you want a good step by step procedure I would recomend back-ordering the febury 2002 issue of street rod builder. It has a great 90 step procedure with pics for each step I found it most helpful!
03-01-2002 03:22 AM
Tom most automotive paint stores carry fine line tape the one I get most often is a 3M product but there are other brands, I do most of my dealings with Sherwin Williams they also carry House of Kolor paint products
02-28-2002 09:29 PM
79monte Thank you much gents, where can i find the fancy tape. I just might try all 3 at once. you never know.
Thanks
79monte
02-28-2002 04:50 PM
stoke46 the way I have always done it is. Draw out your flames, then follow your flame lines with 1/4" masking tape using the inside edge for the outside edge of the flames. After this is done cover the entire area the flames are with paper> I have used plain old newspaper taped together to do this. Then take a grease pencil or crayon and rub the newspaper so the tape layout underneath shows thru. I then take an exacto knife and cut out the flame design, cutting down the center of the 1/4" tape underneath. When this is done I go back and tape the paper down on the exposed edge of the 1/4" tape with either3/8 or 1/2" tape this should leave your flame design ready to spray. I know this sounds a little complicated, but I have done many flame jobs this way and it works,good luck
02-28-2002 04:14 PM
johnnymopar Before you do what tom suggests, i've seen videos on this before. To get each side of the car symetrical you have to draw a pattern on paper. Then you get a pinwheel and trace your lines. Then you position it on the car and use chalk dust on the perforations. Remove your paper and then you can tape off. This way each side will be the same.

JB
02-28-2002 04:09 PM
Tom You are going to use fine line tape this is a product made for that type of work it is a plastic tape that bends and stretches very easily to go around corners and comes off without damage to the surface it also cuts a fine edge when removed, it comes in 1/8, 1/4, 1/2,3/4 and 1 inch widths nice product.once you have the design taped off use a 3M pad to scuff the exposed surface so the new paint will stick paying attention to the edges. then paint it
02-28-2002 12:18 PM
79monte
Suffering Flames

Please help. I love the flame look and i can draw flames really well and wnat them on my car, i also want to do it my self. what is the procedure for tapping off the pattern and not messing up the design when you remove the tape.
Thanks for you help.
79monte

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.