Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Cleaning aluminum
User Name
Password
lost password?   |   register now

Thread: Cleaning aluminum Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-09-2004 09:25 AM
302 Z28 Got a quote on a 50lb bag of crushed walnut shells from a local blasting supply outfit, $15.95 not too bad. That is how I am going, it's lots cheaper than glass beads, and safer.

Vince
10-08-2004 08:44 PM
GypsyR Glass bead blasting works great. I've been using it to restore antique motorcycle parts (OK, and car stuff) for years. If it degrades the surfaces at all, I've never been able to tell. Note that motorcycle parts tend to be highly visible and inspectable when they back on the bike. Unlike transmissions which spend 99% of their lives hidden up in a transmission tunnel. No reason they can't look nice too though.
10-08-2004 09:08 AM
302 Z28 Bead blasting, or blasting with ground walnut shells is probably what I will wind up doing. Both those alternatives offer less surface degradation. I need something that is going to clean all the little recesses that other methods cannot touch.

Vince
10-08-2004 09:03 AM
troy-curt Bead blast makes them look like new.

Troy
10-08-2004 08:42 AM
MI2600 What about a fine wire wheel?
10-08-2004 08:38 AM
paperairplane I have used aircraft paint stripper on painted aluminum parts prior to polishing them with pretty good results, but this was on clean, painted parts in good shape. (polishing motorcylcle parts)

For road grime, what about pressure washing?
10-08-2004 07:35 AM
302 Z28 Sanding is out of the question, I do not want to change the surface finish of the transmission cases.

Vince
10-08-2004 07:11 AM
Dreadlord im not great with aluminum but try some rough sand paper for the heavy stuff and then finer grit when you get closer to aluminum and then buff and polish the rest away.... like i said i dont work with it alot just giving some ideas
10-08-2004 06:47 AM
302 Z28
Cleaning aluminum

Recently came into a heap of Muncie four speed parts, gears, mainshafts, cluster gears, cases, tail housings, side covers, and midplates. Cleaning the gears and everything non aluminum is easy, what do your guys recommend for cleaning the aluminum. Sandblasting is out, does too much damage. Oven cleaner turns aluminum grey. I need something that is going to remove road grime, and in some cases paint. I have tried acetone, MEK, lacquer thinner, Gunk carburator cleaner, and Berrymans carburator cleaner. The Berrymans did so so, the Gunk stuf is absolutely worthless.

Vince

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.