Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Piston to valve clearance
User Name
Password
lost password?   |   register now

Thread: Piston to valve clearance Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-15-2004 01:31 PM
Max Keith
valve clearance

Where he to have a lot higher lift and longer duration in his cam, I would have recommended more clearance on the clay measuring. I do agree that probably .100" should be the minimum under usual circumstances.
11-15-2004 09:16 AM
machine shop tom
Re: valve clearance

Quote:
Originally posted by Max Keith
When you clay the pistons to get an imprint of the valve, measure the imprint with a micrometer and you should have a minimum of .050" thickness.
That's a little too tight. Most of the time, .100" minimum for exhaust, .080" for the intake is recommended.

However for your application, your lift, duration, and timing events tell that you will have no problems, unless you install the timing components incorrectly.

tom
11-14-2004 10:23 PM
lluciano77 You won't have any problems with that cam.
11-14-2004 08:34 PM
Max Keith
valve clearance

When you clay the pistons to get an imprint of the valve, measure the imprint with a micrometer and you should have a minimum of .050" thickness. Anything thinner could translate to eventual valve/piston clash if your valves should happen to float.
At higher RPM your valves can actually stay open at max lift for a longer period of time as the lifter may actually come off the lobe when it hits the return side of the lobe. when this happens, thats when you could wind up with a valve coming in contact with a piston. Just be sure you have the correct tension springs for your cam and dont try over revving it; turnging it higher than the grinders recommended rpm range.
11-14-2004 07:47 PM
BOBCRMAN@aol.com At .465 lift you should have plenty of room... BUT check it with a piece of clay,, just to be sure!!
11-14-2004 07:42 PM
1 Day
Piston to valve clearance

I will check the archives for information later on but can any one tell me offhand if piston to valve clearance will be a concern in this application. 327 bored .40, resurfaced deck, .100 domed pistons, .465 lift cam, Edelbrock RPM heads, 70 cc chambers, 170 runners. I'm not sure what the piston to deck distance is. Thank you, awesome amount of great info on this site.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.