Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 727 trans no forward gears
User Name
Password
lost password?   |   register now

Thread: 727 trans no forward gears Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-21-2004 04:22 PM
Crosley If you have a mismatch of the input shaft / drum design and the pump cover ( aka stator support) ..... it will not function correctly.

The clutch pack is fed differently with sealing rings in different locations
11-21-2004 10:57 AM
stu It doesn't matter what year they are out of or from. It must have feed holes.
11-21-2004 10:53 AM
gorf24 So are you saying i can't drill it, I have had the shaft for 6 months or more and will not be able to return it.... I looked in another trans book and indeed it showed the two shafts the pre 1978 had a hole and 78 and later had no hole mine is a 1977.... so i guess this might explane the problem...
11-21-2004 10:48 AM
stu If there is no hole remove the shaft and install another one.
11-21-2004 09:50 AM
gorf24 I tried that but no good, after taking a closer look at the input shaft I noticed there is no hole between the 2 metal seal rings, looking at the picture it appears to have a hole there but had to tell, if it indeed needs a hole can i drill it?... It's a new input shaft i took and had pressed in...
11-21-2004 08:39 AM
stu Do this.
Place the pump face down in a vice.
Don't tighten it too much, just enough to hold.
Install both drums.
Air check the system.

You should be able to apply the forward clutches by placing a finger over one hole in the input shaft and applying air pressure to the other.
You do have the metal sealing rings installed on the input shaft?
They are the correct size?
11-21-2004 08:32 AM
gorf24 I did an air pressure test and the rear cluches are not moving in case... then i pulled the pump and fount and rear cluches, no i did a bench test still on rear cluch movement, i then disasembled the rear clutchs and did a presure test i get no air presure going to the rear cluch, i will get it sometimes but not most of the time the holes are not clogged its almost like the proper holes are not lined up i tryed it with the shim and without but the same result its a new front shaft, i just can't tell if all the holes line up after i lay the clutches onto the pump for testing.....

Thanks gary
11-20-2004 11:50 AM
Crosley As stu points out the clutch drum you need to inspect..... it has the input shaft pressed into it

hope this helps
11-19-2004 08:15 PM
stu It isn't the front clutches at fault. They are direct and reverse.
It's the rear clutch pack. Those are the forward clutches.
11-19-2004 06:20 PM
gorf24 yes i replaced the piston seals and the spline was fine...
I started pulling it out today will be tearing it down to see what might be the problem, I am going to check the seal in the front cluches to see if that maybe got messed up, it seems to have good fluid presure and if the seal is broke the clutches won't engage, correct me if i an wrong...
11-19-2004 03:45 PM
stu Did you replace the piston seals?
Did you check the splines in the rear annulus gear?
11-18-2004 05:26 PM
gorf24 It has the proper seals, I replace every thing clutches seal bearings bushings, front pump gears, tourqe converter, its not a lockup unit, i did not replace the value body but cleaned it good befor replacing.
I have no forward gears at all no 1,2,3 manual shifting or not, it seems like a fluid presure problem to me but i hate to pull it out till i know were the problem is.
Are the ways to test the presure while running other then the coolant line.

Thanks
11-18-2004 05:02 AM
stu Did you assemble the forward clutch properly?
Did you install the correct sealing rings on the input shaft?
Will the transmission move forward in maual low?
11-17-2004 07:48 PM
fixem all 727 aka as tourqflite came with lockup and non lock up tourq converters and if mixed up will result in no drive condition

check valve body it can also be there too me and my buddy had trouble with one and ended up replacing it!
11-17-2004 07:41 PM
gorf24
727 trans no forward gears

I have a rebult 727 trans new clutches, plates, bushings, pump
forward/reverse bands, tourqe converter...
But i get no forward gears, only reverse.
Anyone have any sugestions as to want i shoud check or be looking for.?

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.