Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> S10 2X4 lift ???
User Name
Password
lost password?   |   register now

Thread: S10 2X4 lift ??? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-13-2005 12:31 PM
daimon1054 I'll try and get some next time I see him. It was only a 2" lift so there's not much visual impact. He is going for the Pre-Runner look so next up is a body lift. We were going to do a larger suspension lift but they all need new rims and he did not have the money for that.
01-13-2005 09:41 AM
Frisco Glad to hear that you got the job done OK. It would be nice if you would post some photos for all to see the finished project.
01-13-2005 09:19 AM
daimon1054 Well I got it done and as said getting the old out was no problem but getting the new spring was not possible without a compressor so I rented one from Auto Zone. All in all very easy project.
01-13-2005 06:55 AM
1ownerT Something to consider, the replacement springs should be much longer than the springs you are removing. Since this is a lift kit,
you will most likely need a spring compressor to aid in the install.
You may find that the upper a-arm will bottom on it's bump-stop preventing you from being able to connect both ball joints.
01-12-2005 08:16 PM
knuckles sorry i did not mean anything bad by it.i guess i put my foot in my mouth any who good luck and have a nice day
01-11-2005 06:27 AM
daimon1054 OK first LOL I am wondering who would not have the truck in the air first whak it with a hammer and let the parts fly. then just dang shame in todays world you have to say that.
I was going to do a full lift with a-arms and spindles but the rims he has will not work so am going to do only the springs and shocks. Still waiting for the parts. Thanks for the input.
01-10-2005 10:19 PM
knuckles what you do is... remove the lower ball joint from the spindle.
i usually leave the nut on anwack it with a hammer.
once the ball joint is loose... let me back up for a minute.
first support the truck on jack stands, and use the floor jack under the lower a- arm..anyway once the ball joint is loose release the floor jack and the spring will push down on the lower a-arm usually releasing it from the truck safely[you may have to push down on the lower a-arm a lttle bit to get it out completely]
i have done this several times and it works for me.i don't like to use spring compressors because they are more of a pain than they are worth. good luck
01-07-2005 05:24 PM
Jzarczyn you don't need a spring compressor. Chain the spring to the frame, and pry it out with a LONG prybar.
01-07-2005 11:26 AM
daimon1054 I have pulled some that you could release all the tension by lowering the lower arm and some that even with the arm down the spring was still in tension. I have no idea where my compression tool is and I don't do this much any more so I am trying to be cheap. I know the danger if you can not release the tension so I was looking for someone who might have done it.

OH well if there is tension I'll just put the wife in front of it
01-07-2005 09:38 AM
Frisco I pulled the front springs on a '51 Ford many years ago without using a spring compressor. It worked fine.

I recently pulled the front springs on my son's '65 Chevy II and made a spring compressor to do that job.

Use a spring compressor! It will make the job much easier and definitely much safer!
01-07-2005 08:14 AM
montea i have never removed Front springs before but i would have to recommend a spring compressor because a friend of mine knows somone that removed a spring on his car and didnt use a compressor and the spring shot out and hit the nieghboors garage door and if the guy was in the way it would of killed him.

somone on here will say the right way to do it. but make sure you do it the right way because it is so dangerous.
01-07-2005 07:14 AM
daimon1054
S10 2X4 lift ???

My nephew just told me he ordered a lift kit for hit 2X4 S10 and that was going to be lucky enough to help put it on it has a-arms and springs on front.
So my question is do I need a spring compressor to remove the spring or will the spring release when I lower the a-arm?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.