Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 500 caddy engine
User Name
Password
lost password?   |   register now

Thread: 500 caddy engine Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-31-2005 02:19 PM
Troadster I saw a 455 Olds in a S-10. It did nothing but destroy the tiers If it ever would hook I bet the rear end would self detonate
01-31-2005 01:50 PM
beyondhelp once I get the pix uploaded you'll be able to see the humble beginnings of my project. I'm stuffing a 472 into an 80's s-10. I can't wait to get this thing running.
01-30-2005 07:10 PM
Troadster
Re: chevette???

Quote:
Originally posted by Jerry Kelley
Wow,that would be one hairy ride,but FUNNNNNNN.
It was in the article. with 3.00 gears and 26" tiers(used front wheel drive slicks) run I think in the high 13's

Please forgive my pore spelling
01-30-2005 07:01 PM
Jerry Kelley
chevette???

Wow,that would be one hairy ride,but FUNNNNNNN.
01-30-2005 06:51 PM
Troadster Did you guys ever see the article in Hot Rod Magazine were thy put one in a Chevet??
01-30-2005 06:27 PM
Jerry Kelley
Cad power

The big Caddys make excellent truck engines,lots of torque and good gas milage too.
01-30-2005 02:38 AM
SnakePliscan
Swaped into 76 Ventura

Yea i droped one into a 76 ventura (Same frount clip as the camero) Replaced stock buick 350, bolted right up to the BOP turbo 350
the swap whent pretty smooth, the Caddy eng is wide so the exh.
manifolds hit the upper A-arms i ground the arms for clearance
but i still had to put the engine in at a very sliyt angle. I hung the engine with my hoist in the eng. bay and welded plate between caddy motor mounts and frame.
I biult my own dual exh.
The one thing i wish i had done was re-cam as the stock grind is pretty mild
Fuel econemy was acceptable, lots of torque.
06-30-2003 11:29 AM
Biggarmike My neighbor had a Caddy 502 in a '58 F-100 pickup years ago, tall enough gears for a top speed of about 80, pulling your house! (at 8mpg)
called that beast the "Fordillac"
06-28-2003 04:01 AM
68_6cyl_camaro how about one big bad caddy hearse? not gonna go fast but it sure would be cool to see a hearse light up the tires!
06-26-2003 10:28 PM
jimfulco http://www.cad500parts.com
www.500cid.com
06-25-2003 09:35 PM
Ohio-Dan What car do you want to put the Caddy motor into? It fits into quite a few with minor "Do it your self" mods.

Someone mentioned a Camaro. A 70'-81' Camaro or Firebird would be a good choice. They come with an 8.5" 10 bolt rear that will take the Caddy torque without problems. Two small steel plates welded to the front of the cross member will allow the stock CDV mounts to be used. You will have steering shaft clearance problems that can be fixed by unbolting the column from the firewall and moving it as far to the driver side as possible. You then redrill holes to bolt it back down. Your main expence will be making an oil pan, or finding an Eldo pan with a rear sump.(I am assuming your car is a Coupe DeVille). The CDV manifolds will work. The right side will be tight against the front of the upper A-frame. You can use a 77'-79' 425 manifold that has a dimple to clear. The 425 manifold is a little more restrictive though. Headers on the stock motor will only net you 10 or 12 HP. More as the motor gets built up with speed parts.

In stock trim, your motor will make around 300 HP on a dyno. Stock compression is rated 8.2-1 with a 120cc head(Actual is around 7.9-1). A switch to a set of 425 heads, with 96cc chambers will give you 10-1 compression and a 45HP increase. The early 76cc heads found on 73' and older Cads will bump your compression to somewhere in the 12.5-1 range. Pontiac valves can be used in the 96 or 120cc heads. The 76cc heads use a longer valve. A 2.11" Pontiac intake valve will flow quite a bit more than a stock 2.000" Caddy valve. You can buy an Edelbrock Performer intake for around $250 or get nearly the same results from "Home Porting" your stock cast intake. An easy 25HP can be had by removing the webbing form under the carb and adding a 1" open spacer.

HotRod did a Junk Yard Jewel artical on the 500Cad.
http://www.eldocountry.com/hrmtorque/

Expect a mid 14 sec pass from your first outing. Once you figure out how to hook all the torque the Caddy has to offer, it will run 13's in stock trim with a 2.56 gear. With a cam, compression, and intake mods, you will be knocking on the 12 sec mark. With a 3.08 gear and a 200 shot of spray, low 11's should be expected. To go faster, one should think about forged pistons and rods to replace the stock cast Caddy parts. 10's would be asking a bit much of the stock bottom end......Wouldn't it? Dan
06-25-2003 04:20 PM
78 monte How bout a 500 caddy motor in a Tubbed Gremlin theres an idea............Oh forgot....its taken.
Did you get my PM return???
06-25-2003 03:16 PM
HemmiGremmie Let me know if you got my PM. My comp was acting up and I wanted to make sure you got it. HG
06-25-2003 02:33 PM
FiefSS Was the 500 the biggest V8 caddy engine? Even so that would sweet to have in just about any car, not many people would suspect a caddy engine in a Camaro, thats something different and would rock
06-25-2003 02:22 PM
woodz428 It should easily fit eng/trans in any mid size GM and probaly not to hard a fit into a Camaro/Firebird. If you want a Big car, it should be a virtual drop in for any big GM vehicle.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.