Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Chevy 350 rebuild....LOST oil pressure HELP!!!
User Name
Password
lost password?   |   register now

Thread: Chevy 350 rebuild....LOST oil pressure HELP!!! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2005 07:27 PM
edge
Quote:
Originally Posted by wed68
What could have caused this, ...
Regarding the bearing damage - No oil pressure at idle. The question should be, why did you lose oil pressure to start with? Ed
02-20-2005 05:04 PM
wed68
Bad news but bad as well!

I dropped the pan and found what I had been expecting, all bearings rod and main were scarred bad! I will pull the engine and start over, new crank and such!

What could have caused this, I believe that due to the fact that all bearings were scarred that I must have started the engine with trach still in it, I pulled the ultimate f>>> up I did not clean the oil gallerys before assembly, I thought the vat was enough!

I will keep yall posted!

Thanks for the Help!

Bill
02-20-2005 01:05 PM
tresi
Quote:
Originally Posted by NAIRB
If you have metal in the filter and you have no oil pressure at idle, you have an internal problem. There is no quick fix, so I would stop starting the engine, as you are going to tear something up even worse by doing so.

Pull the engine and start over.
I'll second that. I'll add that just becuase the machine shop cleaned the block doesn't mean that you can call it clean and put it together. Some machine shops will hand wash the block with hot soapy water and rifle brush the galleys but they often charge extra for that on top of the normal block cleaning charge.
02-20-2005 10:19 AM
arch Surprised nobody said anything about the pump itself... Is it a new pump? or the old one? maybe something broke on the pump itself?
02-20-2005 09:50 AM
SkyMan9600 Thanks 78, I was beginning to wonder if my theory would be correct with his problem also... I'm just surprised no-one said it way before me, that's why I didn't know if it was feasible. When it happened to my bro's car, it had no oil pressure period, lol.
02-20-2005 09:38 AM
NAIRB If you have metal in the filter and you have no oil pressure at idle, you have an internal problem. There is no quick fix, so I would stop starting the engine, as you are going to tear something up even worse by doing so.

Pull the engine and start over.
02-20-2005 09:34 AM
78 monte If you've ruled out the gauge.Drain the oil and examine it for metal particals.Then stick a coat hanger in the drain hole to see if the pickup is laying in the bottom of the pan.I had that happen on a new motor w/ 10k. Had like 45psi moving and 4psi idling.If thats the problem you'll have to drop the pan and put the pickup back in and have it tacked to the pump.Also should prolly pull a few caps and check for wear if thats the case.
02-20-2005 09:13 AM
85 vette A while back someone wrote in an interesting way to check main shaft bearing pressure. I'm not sure if it's even valid but most people that read it seemed impressed by the logic. Basically, you pick an rpm, say 2000, then you do a standing brake rev, bringing the rpm's to 2000 . Don't let the wheels spin. Note the oil pressure at 2000 rpm. Next, put the car in neutral, bring the rpm's to 2000, again noting the oil pressure. Supposedly, if your oil pressure is higher in neutral at 2000 rpm than under brake rev pressure at 2000 rpm , then your bearings are losing pressure. The lower the pressure when brake revving, the worse the bearings are. Sounds feasible. I guess normal would be when both readings are the same. Maybe there is someone out there with knowledge of this theory that could corroborate or dispel it. Rick
02-19-2005 07:41 PM
SkyMan9600 Have you made sure that your oil pickup tube in the oil pan is not sucking itself to the bottom of the oil pan??? It would not get oil then and my brother has had that happen before, just a thought! The easy way to tell that is take a valve cover off (either side) and if it's not spitting oil into the head and it's not the sending unit then chances are it's probebly the pickup tube in the pan... Just my worthless two cents

*Edit* - Sorry, didn't see your post right above this one, if you're going to drop the pan, go ahead and check it when you drop the pan, you might be surprised at what could be going on...
02-19-2005 07:40 PM
wed68 yes new cam bearings, I am going to drop the pan tomorrow and start checking bearings! I think I spun one or something!

Bill
02-19-2005 05:03 PM
lluciano77 It could be a bearing issue. Did you have a shop press in new cam bearings?
02-19-2005 04:54 PM
wed68 Update! I change the oil today to 10w40 but no change. I did find pieces of what looked like bearings in the oil filter. When I started it cold it had good pressure. I then found an oil leak on my sender unit, I changed it but the same thing little pressure at idle but about 30 psi while driving!



Bearing spun?

Oil pump came apart?





Bill
02-19-2005 08:09 AM
4onthefloor 2 pull off the rocker cover and see if any oil is pumping through the rockers while motor is running
02-18-2005 07:50 PM
RCastle Pick up a good mechanical oil pressure gauge. You can hook it up and not make a permanent fixture in your car if you need to. You could hook it and mount it under hood to check what it is at idle and with the engine running thru the RPM band. Good mechanical gauges are not expensive and are a direct piece that will read regardless of whether there is a circuit problem going to the electric. Your sender pulls a signal from there it sends it to the circuit board in your dash panel.
02-18-2005 07:50 PM
wed68 I did not weld the pick up tube on, would I have any oil pressure at all if it worked loose?

Bill
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.