Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Control Arm bushing replacement
User Name
Password
lost password?   |   register now

Thread: Control Arm bushing replacement Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-14-2005 08:06 AM
aminga I went out and bought an Astro Master Ball Joint service kit. And I've used it for ball joints, U-joints but more importantly control arm bushings. You still have to be careful though when pressing them in/out not to crush the arms. A small piece of wood cut in the proper size and wedged in around the bushing works nicely to keep things from crushing in.
03-14-2005 06:09 AM
redlightning You can get a large bolt and some washers.Put the bolt through the bushing,place the bushing in the control arm the way it is supposed to go.On the other side get a socket larger than the diameter of the bushing.Get more large washers and a nut.Then tighten the bolt and nut.It should press it in.
03-14-2005 05:03 AM
RCastle Use Vaseline or White Lithium Grease. I use the spray type of Lithium when I install new bushings in radius rods and torque arms at work. I also have a press though. I have never tried beating them in.
03-14-2005 12:06 AM
1Fast65Elky I used a hammer and a pipe the diameter of the bushing on 2, and the other side i used the help of a hydraulic jack, Redneck press
The jack worked better, but you run a good risk of bending stuff.

Bushings in the freezer sounds like a good idea Make em shrink.
Also seen someone mention in an old post to put vasaline on em.
03-13-2005 08:23 PM
montea somone on here said that they put the bushings in the freezer for a day or 2 and they shrink enough to fit in easily.
03-13-2005 07:14 PM
poncho62 Use a press.......................Hammering them in may bend the arms, they aren't that solid.
03-13-2005 07:06 PM
bonuts C'mon somebody has replaced control arm bushings.... Right... guys...GUYS

Just a shameless bump, I'm going to do this in the morning, kinda need some help.


bonuts
03-12-2005 04:35 PM
bonuts
Control Arm bushing replacement

OK heres the deal, My 24 yr. old S-10 needs the front suspension bushings repleced. As I have never done this I'm going to need some help.

I have disassembled the front, burned the old bushings out of the lower control arms, (cause I don't have a press,and a hammer wouldn't do the trick).

Now for my problem. Do the new bushings need to be pressed in? Does anybody have another way of doing this? If the new ones do go in easily, do you have to tack weld the sleeve to control arm, or does it matter?


Any help would be appreciated


bonuts

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:42 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.