Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 350 crank with BB snout
User Name
Password
lost password?   |   register now

Thread: 350 crank with BB snout Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-15-2005 04:42 PM
mackyLS6 Thanks guys for responding. I'll take that advice and call some blower shops and ask about some setups.
56Maynard, sorry, my intended use is for the street and some show'in off. I will definitely check out RBS superchargers.
Camaroman7d, My machinist referred to the snout as a BB snout, but in some of the catalogs I've seen they refer to it as a 'large snout', typical of the cranks used in stock car engines. Thank you for the info on the crank hub, another option to look into.
Thanks again.
03-15-2005 04:01 PM
56Maynard You didnt mention the intended use. Street or Strip? If you are gonna race it, you can get a crank support and a large snout.

At any rate, check in with RBS Superchargers and ask for JR. He will set you up and he's honest.

rbssuperchargers.com
03-15-2005 03:30 PM
camaroman7d I have never personally heard of a small block crank with a big block snout. Your machinist is correct a blower can put a lot of added stress on the crank snout. Since SBC snouts are pretty small, you will want to run a short water pump (this keep the pulleys, etc.. from hanging out too far and creating more stress). What I chose to do is run a crank hub and no balancer/damper this allowed me to get rid of a lot of weight on the snout. Call a few blower shops and get some input before you buy any parts. I personally don't think you need a big block snout, if you have a good strong (forged) crank and keep the stress to a minimum.

Royce
03-15-2005 03:02 PM
mackyLS6
350 crank with BB snout

Hello friends,

I am about to start building a sbc 350 motor and my intentions at this time are to install a 6-71 blower on it; its just something I've always wanted to do.
I told the machine shop about my aspirations just to prepare the motor in case I actually bolt on a blower.
The machine shop suggested a forged crank with a bbc snout since blowers have a tendancy to exert greater forces on the crank snout.
My question now is: Does anyone have parts info for this crank, ie; timing cover, timing set (gears or chain?), and balancer ( 1/4" keylock)?
Thanks for your input.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.