Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> finishing fiberglass with moldless design
User Name
Password
lost password?   |   register now

Thread: finishing fiberglass with moldless design Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-22-2003 02:47 PM
swoodard23 I wish I could use a female mold but I am trying to stay within a budget on designing the body. The wax paper idea sounds great. I will have to try to figure out how to use it on some of the curves. I did want to ask if I should still use a gelcoat.
Thanks,
Scott
01-22-2003 05:17 AM
Shawn Asseln After you lay down your mat you can coverit with a good quality wax paper till it gels as to give it a smooth finish and this will also help keep the mat under the surface which is what you want. I have even covered it with cardboard on flat to semi flat areas to hold it true and keep it from sliding. after it is kicked I would attack it with a 36 grit grinder and remove the cardboard and overlaying 'glass, one swipe with a little plastic and ready for primer.
01-21-2003 08:13 PM
willys36@aol.com That's the way Ed Roth made his show cars (Mysterion, Road Agent, Beatnik Bandit, etc). He would spend hours making a pefect plaster male model of the body then lay the 'glass over the top of the smooth plaster. Then he pounded the plaster out and spent countless hours smoothing off the rough fiberglass surface. Give me a female mold anyday!!
01-21-2003 01:37 PM
Halloweenking Gel Coat or another layer of resin sanded smooth. I recomend Gel Coat. Buy it spray it, your good to go.

HK
01-21-2003 12:42 PM
swoodard23
finishing fiberglass with moldless design

I just layed 4 layers of fiberglass mat today and am very impressed with its strength. It was flat and still had very strong characteristics. My question is to see if anyone has any tips on how to get a good surface on it without using a smooth mold. I know you can use bondo, but there has to be an easier(and lighter) way. Perhaps something spray on? Something must be done because the surface is very irregular because of the strand mat. Any suggestions or webpages would be appreciated.
Thanks,
Scott

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.