Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> door jam prep for epoxy
User Name
Password
lost password?   |   register now

Thread: door jam prep for epoxy Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-11-2005 09:51 PM
Bee4Me You can get the pads at Harbor in the sanding area. A box is like $5.00, MUCH cheaper than the parts store's. If they don't have the Gray one's, the Reds are OK for use before the epoxy.
Pick up a spray bottle for the water too, It's alot easier than a bucket.
04-11-2005 05:37 PM
myfamiliacc One wet coat could be good enough but I would go with 2 wet coats.

You can do your body work over the epoxy just scuff it.

Sence you do have bodywork it's best to go with a high build primer. 2 to 3 coats of that.

Block sand it all smooth

contenue with a sealer or stright paint.
04-11-2005 05:23 PM
montea ok sounds good..

the rest of my car is bare metal, going to spray it with epoxy, how many coats do i need? i will not be painting it right now, just be in primer for a year probaly

im going to epoxy over bare metal, use body filler for low spots, then some other kind of primer overtop if that.
04-11-2005 05:21 PM
myfamiliacc Try to get at the chip with some 400 to feather it out smooth, then hit the rest with a grey scutchbright pad. (dry or wet) Though I like scuffing wet with soap water.......cleans and scuffs at the same time

After cleaning it with wax/grease cleaner
spray one wet coat of sealer (epoxy sealer is fine)
followed by your paint after flash time.

Don't use the green scutchbirght bads.....they are too harsh
04-11-2005 04:49 PM
montea its original paint but there is chips in it, just like a green scothbrite pad? do you need to use water with it or dry? Thanks alot!
04-11-2005 04:14 PM
myfamiliacc If it still only has the factory finish, and you don't have any rust, then just scuff them up with a scutchbright pad and go for it.

IF it's not the OG paint, and or, you have rust, then you're best to remove the door, and strip it down to metal.......A spot blaster would be good.
04-11-2005 02:54 PM
montea
door jam prep for epoxy

the door jams have tight places that are really hard to get to and will not get all the paint off to bare metal before applying epoxy. anyone got suggestions or tips on how to get the door jams ready for epoxy?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:08 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.