Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> HOK kpc2f epoxy primer.. not adhering well?
User Name
lost password?   |   register now

Thread: HOK kpc2f epoxy primer.. not adhering well? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-14-2005 08:24 PM
beemdubya Well, my test panel helped me out alot.. the part that had nothing under the epoxy stuck perfect.. what i did was take a razor blade and try and chip it off and get under it.. well needless to say it didnt chip at all on the part of the panel with no etch at all. just kinda scraped the top layer off. i guess this primer isnt so bad afterall. but ill stick to the epoxy i normally use.
04-14-2005 07:09 AM
Bee4Me That may be the one that goes dormant below 70.
The non catylized can be stored in the fridge indeffinetly.
I agree with not using the acid treatment as it can cause you alot of grief.
IF the temp was consistantly below 70,That is most of the problem.
It just quits curing.
04-13-2005 10:54 PM
baddbob I quit doing acid many years ago Metal prep type acid treatments caused me a lot of grief. A clean and textured surface is all the epoxy should need for good adhesion IMO. When you're done cleaning the metal surface you should be able to wipe a clean white towel with no discoloration showing on the towel.
04-13-2005 06:32 PM
BarryK Well, if its been a month, than that is a problem. and only two things I can think of to cause that is,
Not activated properly or the metal treatment not neutralized properly.

If its working on some panels and not others than most likely would be an acid problem.
I would from here on out skip the acid treatment.
04-13-2005 06:21 PM
beemdubya it has been about a week since i primed the door.. i have a couple other parts that i primed about a month or so ago with the same stuff im gonna see how they are doing tomorrow. the temperature has gone down at night but the days have been 70degrees give or take some. if i just skip the metal conditioner will that work... or if i skip the metal conditioner and just give one light coat of the self etch will that work?
04-13-2005 05:36 PM
BarryK You are probably in good shape!

Epoxy does not give maximum bite right away, the first 24 hours if you take a scraper you can probably scrape it off pretty easy after 48 hours you may chip a few spots after a couple of days as the epoxy cures is when you start getting adhesion to the point that it won't scrape off or not feather.

Now also keep in mine that cold metal will slow the above process down.
The above days I'm speaking of would be 70 Degrees or higher.
04-13-2005 04:36 PM
HOK kpc2f epoxy primer.. not adhering well?

So i stripped a door on a car im working on using 36grit and then 80grit paper. Then i cleaned the surface with wax and grease remover and then i used metal conitioner scrubbed it with a red scotch brite pad and let it sit on there for 10 minutes keeping it wet at all times. then i washed it off with water and cleaned it again with wax and grease remover. sprayed my two medium coats of the epoxy on there. well today i was sanding the qaurter panel and accidently hit the door.. the primer chipped and little and got me thinking if this was actually adhering properly.. so i take some 80g in my hand and sand the chip a little bit.. and sure enough it just started coming off and it wouldnt feather edge. so i grab my palm sander with 180 on it and sand it.. some spots feathered some just chipped. out of the 16inches that is sanded i would say 4 inches actually feathered but if i sanded it long enough it would just chip again. i did a test panel about 20 minutes ago.. i did just bare metal with no conditioner and then i put SEM self etch under the other.. if this doesnt work and noone knows what the problem is im gonna throw it away. since it is not what i usually use in the first place it was brought to me by the owner. has anyone used this before?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 05:46 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.