Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 383 stroker kit (Ebay)
User Name
Password
lost password?   |   register now

Thread: 383 stroker kit (Ebay) Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-24-2006 06:51 AM
bigbadbowtie Another for T&L on ebay. Atleast look at them before you buy. They actually check ALL clearances before shipping.
05-23-2006 08:35 PM
crazyrs
383 stroker

bought my kit from t&l engines they are great pull there web site up t&lengines.com i had them balance my crank fit my rods no problems.
04-20-2005 06:13 PM
lluciano77 I got my SBC 400 bottom end kit from that guy. I did a lot of research before buying, and this kit was the best for the money by far.
04-20-2005 06:04 PM
67 Deuce 4 Me I bought a 383 kit from that same guy a couple years ago.I was very happy with it. He was a nice guy, I got free shipping and he clearnced my rods for free!
04-20-2005 04:15 PM
Hazard Well, I'm planning to use an XE274H-10 cam from Comp cams 230/236 duration. As for compression, I'm trying to keep it around 9.5, so I'm going with dished pistons due to the vortec 64cc heads that I'm going to use, Edelbrock Performer RPM intake, 750cfm holley, 1.6:1 roller rockers, springs specified for cam. I'm starting from scratch here, so all parts going to be used are going to be new. It's going to take a while to finish this project, but I'm trying to get into the low to mid 400hp range. Any recommendations on this setup? I'm still undecided about the cam, but that's the setup I'm starting off with.

Let me check out Racers Outlet on ebay and see what I can find.

Thanks,
Martinez
04-20-2005 11:44 AM
MI2600 The ad says it's balanced, which usually is done with the balancer and flexplate.

Checked his last two negatives and they were about shipping and paypal. Nothing about quality.

Sounds like a decent deal.
04-20-2005 09:38 AM
GoneNova/406 i have a 406 2 bolt but got a 4 bolt this past winter and built a new motor after first buying all my parts except the crank (and it was the same price and i saved on shipping at jegs) from kevin at racers outlet on ebay.he specialize's in sbc parts but has all others.he has great prices.you can't go wrong.he treats you right on the shipping prices too.check him out,you won't be sorry.the only bad thing about him is hes only there 4 days a wk. for a couple hrs. a day.but to save money you can work around that.
04-20-2005 01:30 AM
ChevyThunder Well it all depends on what you want to do as far as power and such. I mean for a basic daily driver cast crank and I beam rods are fine. The other thing is depending on what compression you are running, with cam lift, rocker arm ratio and such you may want to be able to make sure your your pistons have the proper valve recess. Of course for your average rebuild these things aren't much of a problem, but I'm guessing since you are looking at doing a 383 you aren't just wanting a normal rebuilt 350.
04-19-2005 08:51 PM
Hazard
383 stroker kit (Ebay)

Hey guys. This is Hazard once again with another question on my 383 stroker project. I finally found a machine shop and my next step is to purchase my stroker kit. I have looked around and checked out prices on individual parts as well as complete stroker kits. What do you all recommend when buying the rotating assembly? I don't want to spend on fancy parts or just throw away my money. I'm now debating if I should purchase a stroker kit that is sold on ebay or just buy item by item. I don't want the engine for drag racing. The home of this engine will be in an 89 chevy regular cab that I'm restoring inside out. Going to be a weekend truck. I know this is one of the cheap kits, but how decent are this kits? Here goes the link for one of the kits I ran into on ebay.

http://cgi.ebay.com/ebaymotors/ws/eB...category=46098

Also, if the kit comes with flex plate and dampner, would the balancing be reliable? Would hate to rebalance if not necessary.

Also, thanks for all the feedback you all have provided on my prior threads.

Martinez

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.