Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Engine just dies
User Name
Password
lost password?   |   register now

Thread: Engine just dies Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-29-2005 11:51 AM
Siggy_Freud This post was started by me about 4-5 months ago. It required a reworking of the computer chip as well as playing with the IAC settings.
04-29-2005 10:45 AM
SmallBlock_guy
Engine just stops??

What do you mean the engine just stops. Give me more details. Does it try to stay alive or below 850 and gone!
By changine the rocker ratios you may need to play with the idle fuel. Also look at the MAP readings are they the same with the new set up??
12-03-2004 07:35 PM
scholman Siggy-Freud,

With the addition of the 1.6 rockers I think the valve overlap is making your engine run as though it has a larger lift cam.
I would leave well enough alone and drive the car a few weeks and then check things out again.

Just My .02
Scholman
12-03-2004 07:14 PM
Siggy_Freud I just changed the heads and went to 1.6 Roller rockers. I would hope the heads flow a lot better than the stock heads lol. The timing was set in the correct procedure however I am going to play with it some more and see what it likes. I just feel that having to idle in drive at 850RPM means something is a miss. It did have to idle fairly high before. Is it possible the new heads and airflow mean it will have to idle higher now? Still seems like something is amiss.

Gone is fuel injected so no carb to mess with. I will open the butterflies a little more but the Idle Air control valve (which is new) should take care of idle air.
12-03-2004 07:05 PM
GoneNova/406 what specifically did you change?go to better heads?change the breathing habits ofthe carb.?
12-03-2004 06:30 PM
spinn you probably know just what i know(or more). here are a few ideas. double check everthying . like your base carb settings.

when you set the timming do you half to jump the service connector? on ford there is the spout connector. did you have a similar procedure to do?

you may have to recalibrate the computer. or let it adjust with a idle relearn

have you tried increasing the fuel psi just to see what happens?

pull the vacuum line off the psi regulator and plug it.
12-03-2004 06:25 PM
Siggy_Freud
Engine just dies

Just finished up installing some new Trickflow cylinder heads. They are now sitting atop a 350 with a TPI. THough I do not know the specifics of the cam, I know its fairly mild from its idle and powerband before the head swap.

It will start and run smooth, and then a little rough but for the most part smooth above 1000 rpm. Anything below 850 or so and the engine shuts off. I have checked for vacuum leaks and there are non. My vacuum guage shows 15 inches of vacuum which is pretty much where it was at before the head swap. Timing is set at 6 as this is a stock setting for a TPI. The comupter takes over after that. Fuel pressure seems great for it at 48 (I can adjust this and will to help out once things are set). If I take out the pcv and have the line open, it climbs in RPM's.

There is no backfiring or poping and like I said it seems to run great above 900-1000 RPM or so. Is it possible my cam is bigger than I thought and the new heads (which replaced stock junker heads) are causing the cam to act bigger? In drive it will die at anything less than 850RPM.

Any ideas?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.