Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > General Discussion> Hotrodders' Lounge> parts cleaning ideas???
User Name
Password
lost password?   |   register now

Thread: parts cleaning ideas??? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-01-2005 06:04 PM
jesse01 QUOTE]gas is too expensive to waste these days.[/QUOTE]

good point didn't think about that either

J
05-01-2005 05:22 PM
poncho62 Besides the danger factor.......................gas is too expensive to waste these days. Get some kerosene or fuel oil.....at least it won't blow up in your face.................burns more slowly.
05-01-2005 04:57 PM
Hippie Castrol's cleaner does a good job, so does brake cleaner. Best stuff was Hydro Seal carb cleaner by Gunk but you can't buy it anymore, seems it's main ingredient was methylene chloride....... bad stuff.

Everyone that stuck their bare hand in a bucket of it "real quick" to fish out a stray part raise their stump.........
05-01-2005 04:17 PM
61bone it shouldn't hurt anything. as long no cig's or flame is around. right?

[/QUOTE]
Wrong Static from your clothes can set it off. Ever take your coat off and get zapped by the first thing you touch?. Any steel on steel contact can set it off. Ever drop a wrench on a conctete floor in the dark? They spark.Take it from a guy whose been there . Don't use gas for cleaning. Don't store it in an open container. If it's not in your gas tank, don't have it in you shop. Build a small ventilated box to keep it in outside. If gasoline were introduced as a fuel today it would never be approved because of it's highly volatle unstable nature.
If the crud is really that bad, get it media blasted, preferably with walnut shell. If you get it glass beaded in the runners, throw it away and buy a new one or scrub the runners with soap and hot water till your arms feel like they're about to fall off, the do it about twice that long again. The beads are killer if they get in your motor. Another thing you could do is get some carb cleaner and scrub with a wire brush. Don't forget eye and skin protection.
05-01-2005 03:24 PM
jesse01 its all apart in pieces i could just pour the gas in it & let it work it's way through all that crud & let it drain.

it shouldn't hurt anything. as long no cig's or flame is around. right?

a tried some "heavy duty engine degreaser" and all that **** on the inside of it just laughed at it , it didn't phase it at all

j
05-01-2005 03:14 PM
61bone : You'r going to feel a lot dumber when you bang a couple wrenches together and it explodes in your face. Never use gas for anything but it's intended purpose (smokin tires).
Use a little electric contact cleaner to clean your flow sensor. Invest in a 5 gallon pail of regular non flammable parts cleaner for everthing else.
05-01-2005 03:01 PM
jesse01 duhh! why didn't i think of that??

something so simple as gas. you know what? i use that stuff all the time at work to clean the "blackjack" (tar) off of my tools when it gets on 'em. i feel dumb now

i would of figured it out when i went to work tom.

j
05-01-2005 02:53 PM
1Fast65Elky gasoline that stuff cleans my greasy parts...just dont light up a smoke. and be very careful.
05-01-2005 02:31 PM
jesse01
parts cleaning ideas???

what the best way to clean out the inside of a tpi plenum & runners????

I've tried degreeser & a rag

Don't laugh but i also tried:

letting it soak in the bathtub w/ dish washing soap like "Dawn"

lol, i even put it in the dishwasher (hope my 'ol lady don't come home any time soon...heheheh)

and it's still black & gritty on the inside

any of ya have any better ideas??

J

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.