Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Ford motor change question
User Name
Password
lost password?   |   register now

Thread: Ford motor change question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-27-2005 09:51 AM
Churchman
Thanks for the info

Thanks for the info so far. The tranny and the 302 are together already and supposedly have been driven but the tranny will not shift right now even though it did before and they think it is bacause it does not have enough vacume, but I have not seen it yet, they may not have the vacume hooked up right. Welding to the chassis will not be a problem and I think I will use your advice on the tube/rectangle bar. Thanks again, I'll let you know as I know more. All info is encouraged.
05-27-2005 07:26 AM
crazy larry THE I6 and FE use the same motor mount. the small blocks, 302,351 use a different mount. a couple inches is the difference. the I6 mount will set your motor too high.
05-26-2005 06:47 PM
Mr Ed i doubt that it will fit using the same engine mounts and they may also be too far back along the chasis rails so you'll most likely need a kit or make new brackets off the chassis, we usually use a bit of box/rectangle steel- weld it to the chassis or crossmember then just drill the hole in it for the mount bolt (that is if you are allowed tio weld to your chassis in your area- we arn't-it has to be welded to a crossmember which is bolted to the chassis).
Check that the trans fits the engine as ford change their bolt patterns all the time so do a visual and check the holes in the rear of the 302 compared with the trans bellhousing.
The vacuum statement is questionable, enignes with big cams can run low on vacuum but basically standard engines should be okay, however you can overcome low vacuum problems by running a vacuum canister or a alternator with a vacuum pump on it such as those found on diesel engines.
You will need a different rear trans mount but may be able to use the existing rear cross member but you'll probably have to move it either forward or backwards. You will probably need a shorter or longer driveshaft too.
05-26-2005 05:43 PM
Churchman
Ford motor change question

I have a 1961 Ford uni-body PU. It has no transmission and a questionable inline 6 motor. I have been given a mid 80's 302 motor and early 90's tranny. Two questions:

1) Will this motor with it's mounts mount into my PU or will I have to buy a kit?

2) The people giving me the transmission said that it would not shift correctly in their mercury because the 302 motor that was added did not have enough vacume for it. Is this possibly correct and Can I just buy a vacuume booster for it? And will I need a different tranny mount?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.