Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Rebuilt 700r4 - no reverse
User Name
Password
lost password?   |   register now

Thread: Rebuilt 700r4 - no reverse Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-10-2005 10:55 PM
Anton thanks for the help. Dropped the pan today and found the valved popped out. I accidentally installed the snap ring into the little machined bevel in the bore, not in the snap ring groove. And to think i actually fought with that for a good 20 minutes trying to get it seat into no groove. Fixed it and works great now thanks
06-09-2005 08:16 PM
Crosley there are two separate boost valves in the same bore in the pump of this 1991 4L60. They are about the same size , different designs though.

the PR valve goes in first , then the PR spring , then the low / reverse boost valve , then the main boost valve , then the snap ring. If these are not installed correctly the pressure will not be correct
06-09-2005 07:47 PM
Anton Trans fluid was a little over filled but I dont see how that will cause me not to have reverse all together.

I checked the number stamped in the case and it is indeed a 91 transmission (according to the haynes manual). Came out of a 91 Astro AWD. I spent a lot of time double checking all the chek ball placments, and everything added up in the end.. with all the check balls in place, I had 2 left over, as B&M said to leave out 2.

Please refresh my memory, where are the boost valves located?
There is one valve on the pump retained by the snap ring, which I had to remove and replace the spring with a B&M piece. I had a hell of a time getting the snap ring to seat properly. Is this the boost valve?

One more thing, I did partially disassemble the pump for cleaning. ONce i had the 2 halves apart I removed whatever i could that wasn't reained with snap rings or clips, is there anything I could have installed backwards? I didn't use a alignment band to put the pump back together, I eyeballed it. The pump installed in the case effortlessly, so it has to be close. Is it critical that the 2 pump halves are aligned perfectly?

Thanks
06-09-2005 08:01 AM
Crosley your first rebuild?


sounds like serious pressure loss.

The B&M shift improver kit may have listed the check ball locations incorrectly or you looked at the wrong year for your application?

TV cable would not affect reverse since line pressure is raised by the low/reverse boost valve.

there are many things that could be wrong.

Check the assembly of the boost valves... often the DIY folks install them backwards or miss the snap ring groove .... then the boost valves blow out of the bore
06-09-2005 04:45 AM
302 Z28 Have you adjusted the TV cable properly? Is the trans fluid level up to spec?

Vince
06-08-2005 10:32 PM
Anton
Rebuilt 700r4 - no reverse

Hi. I just rebuilt a 91 700R4 with the TCI kit, and installed a B&M RV heavy duty shift kit. I carefully followed B&M's instructions for check ball placement.
I installed the transmission today and don't have reverse. I do have forward gears but they seem very weak. I can step on it with my truck in low range and still hold it, with the brakes, and my brakes are BAD.

There doesn't seem to be any engagement in reverse at all

This is my first automatic, and first time rebuilding one, and I don't even know where to start. Any ideas before I go searching for a new transmission?
Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.