Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Rebuilt 327 w/Edelbrock carb revs WAY too high
User Name
Password
lost password?   |   register now

Thread: Rebuilt 327 w/Edelbrock carb revs WAY too high Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-11-2003 04:59 PM
CHEV66JB This is my first day on this group, and already you guys have been a HUGE help. I found out it was in fact the stupid throttle linkage. When I hooked it up, I didn't even notice that it pulled the throttle back about 1.5 inches. I adjusted the linkage and after hooking up the tach, noticed all is running fine!! I only have about 80 things left to do now to drive her this summer (get it tagged, front end alignment, etc etc etc), but this was a huge accomplishment for me today. Thanks to all of you for your input!

Regards,

CHEV66JB
05-11-2003 02:30 PM
Crazy d as deuce said check linkinge for tension it maybe pulling your throtle.did you plug the holes in the carb one in back carb comes with screw in plug and caps.make sure your choke is not on.lower the idle screw on the drivers sides neer where the linkage hooks on.the to screws in front with the springs are the air fuel for now screw them in all the way than open them 1 turns.if your distributor has a vacum plug it in also not sure what side one side for tranny and the other for distr.check your manual came with carb.use the correct gasket it came with carb on big hole not 4 holes.when you get it to run ok you got to rev it to 2000 for 20 min or so to break in the cam look at water and oil gages to make sure nothing goes wrong.better to have a friend there to look at engine and stuff also leaks and ect...
after you can get a timming light and tune the carb.. PS.get a tack before so you know what your reving good luck hope this helps...
05-11-2003 01:25 PM
CHEV66JB And actually, yes, the motor has a new Crane Powermax cam in it as well-
05-11-2003 01:20 PM
CHEV66JB I do not have specific RPM's unfortunately b/c I do not yet have my tach hooked up. I will try to get specific #'s by this evening, however it sounds like it's running well over 2000 RPM.
05-11-2003 01:19 PM
CHEV66JB Hello and thanks for your reply!

I unfortunately do not have a timing light, so I am trying to work through this as best as I can (this is my first time doing a whole motor rebuild from the ground up).

When you say "turn the idle screw out", does that mean to turn it out counter-clockwise all the way?
And this is the main idle screw, not the "fast idle", correct?

Thanks again for your help.
05-11-2003 01:16 PM
johnsongrass1 How high is very high RPM's. Gotta get the details in order for us to make an accurate diagnosis over the net. Many people forget the details. The more the better and the better answer you will get.
05-11-2003 01:12 PM
Deuce

OK

Have you checked for the obvious?
Disconnect the accelator linkage. Turn the idle screw out. Put a timing light on the engine and check the timimg.

IF you put a new camshaft in the 327...it needs to run a 2000PM's for about 20 minutes away

More later if this does not help.....

Do not get discouraged <img src="graemlins/nono.gif" border="0" alt="[nono]" /> <img src="graemlins/nono.gif" border="0" alt="[nono]" />


.
05-11-2003 12:41 PM
CHEV66JB
Rebuilt 327 w/Edelbrock carb revs WAY too high

Hello all,

This is my first post and I'm hoping you all can help- I just finished rebuilding a 275HP 327 for my '66 Chevelle, and am trying desperately to get her back on the road. On the rebuilt motor I am running a stock intake manifold, HEI, and an Edelbrock 1406 600-CFM carb (brand new, just bought yesterday)w/electric choke.

I am new to working with carbs and timing, but thought I had everything set up correctly. Problem is, when starting the new engine, it starts but immediately goes to very high RPM's and all I can do is shut it off. I made no adjustments to the carb out of the box, simply put it on the car and tried it out.

Any help would be greatly appreciated, but PLEASE try to give suggestions in a format I can follow! Every person who has replied so far has given me instructions like I'm a 50 year old mechanic, which isn't the case 8^]

Thanks in advance,

CHEV66JB

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.