Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> spray gun tuning help please..
User Name
lost password?   |   register now

Thread: spray gun tuning help please.. Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-29-2005 09:27 PM
the milkman I have used auto air in my airbrush for a few months, and have had a lot of problems with it being too thick. Your paint my be drying up at the needle tip, and causing it to spit, and could be partly to blame for you pattern. Try thinning you base out about 10-15%, and dusting your coats on really thin. Auto air says you should use there thinner for the binders in it, but I have used only water, and have not had any problems with adhesion. Good luck
06-28-2005 04:43 PM
VWFan I have the same gun and I had no problem shooting Acrylic Enamel with it at the recomended 21PSI at the gun. These guns are budget, but the craftsmanship on mine seems to be very good. I think your problem is in the paint mixture, air pressure, and gun adjustment. It does not take much paint to shoot test patterns, so I would suggest mixing some paint up and just keep adjusting until you get a good pattern. You'll get it, just keep trying.
06-27-2005 03:27 PM
alteredpilot in talking with a few painters, i'm thinking i had too much fluid flow. i'm learning that it doesnt take much of an adjustment to make a dramatic difference...
back at it tomorrow..
06-27-2005 01:04 PM
Bee4Me The banana or curved pattern is a blockage in the airhorn holes. Most touchup guns don't have cap holes other than the main fluid opening.
Could be trash/defect from the drilling during manuf. or from the air supply.
Possiable air leakage around aircap seal where it screws on to the gun.Not the paint nozzel,the "ring" you tighten around the airhorn.Some have an O ring or Teflon washer to seal this.
The Q-tip or dumbell is air/fluid misadjustment,Most likely,too much air pressure as your blasting 55 into the gun. Most HVLP want around 20-30.
Never shot this water base myself but it sounds like it's too thick to atomize properly which is why your cranking it up to 55 and your spray pattern is going to heck..
06-26-2005 05:54 PM
alteredpilot its a brand new gun.
after posting, i figured i oughta take a closer look at my equipment and i went a took the tip off and brushed everything out really good.
i'm gonna go back out and shoot some more later....
any input is greatly appreaciated.
06-26-2005 04:57 PM
kenseth17 Is this a brand new spray gun you are using? Sounds like a couple different problems from all the shapes you described. If the pattern isn't parallel and even and curved in the middle, one of the holes on you aircap could be clogged or possibly something bent. The other patterns you described I don't know, but sounds like too much pressure, and fan pattern turned out too wide. Hopefully someone else will give their ideas also.
06-26-2005 04:31 PM
spray gun tuning help please..

read the primer (npi) in the FAQ thread, but i'm having some other issues.
i'm using a vaper hvlp detail spray gun with a 1.0 tip and i'm spraying the new version of auto air colors. i've tried from 35-55 psi and i'm getting the better atomization at 55. still getting some spattering though.
i did a spray out test and one of two things is happening: either the spray pattern looks more like a banana or a turd than a cigar, a little curved and or the pattern is canted (adjusted the fan tip thingy to compensate)
OR it looks more like a q-tip than a cigar...fat on the ends and light in the middle....
any direction>??

oh yeah....never shot any kind of paint out of a gun in my life so please esplain to me like i'm in the 2nd grade.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:26 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.