Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 400 small block compression and head gasket question
User Name
lost password?   |   register now

Thread: 400 small block compression and head gasket question Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-07-2005 09:49 PM
NXS GM has some steel shims that are .026". I'm not sure if they had steam holes but with that type of gasket it would be childs play to drill them.
07-07-2005 09:48 PM

Look under the piston. You may find a manufacturers name. If so you may be able to get a matching piston. If you use a piston with more or less meat. You are going to put your motor seriously out of balance. If I understand correctly. The small hole in the top of the piston designates (front). The hole goes towards the front of the motor. I would just use a Felpro 400 head gasket. With dished pistons and stock 76 cc heads a .020 head gasket isn't going to do a thing for you.
07-07-2005 09:43 PM
400 small block compression and head gasket question

i took the heads off of my 400 sbc today to inspect the pistons and get ready to swap the cam. My motor is from 72 and it has a dished piston. My friend gave me a burnt piston from a 400 (year unknown) that he had and i compared the two pistons. On his piston there are deeper valve reliefs and the outer edge of the piston has less material than the pistons in my motor. I was wondering what compression ratio my motor might have. The code on the front of the block is T0526CKP and the number on the back of the block is 39511511. Its a 4 bolt main block. Ive read that 400s had anywhere from 8.5:1 to 9.0:1 compression ratios. I was thinking that I might have one of the higher compression 400s because of there being more material on my piston. Also what is the purpose of the small hole on one side of the top of the pistons?

Also Im not sure if the head gaskets that came out of the motor are stock or not. They almost seem to be a permatorque type gasket. They may be a regular steel shim but im not sure. Either way, i measured them to be about .030" compressed. I dont want to lose any compression in the motor so i want to put at least an .030" gasket back in or something not much thicker, preferably a little thinner if possible. Does anyone have any suggestions on what gaskets i should use? Ive looked in summit but i havent found any with a thickness close to .030" with a bore for a 400 with the steam holes. Any help or suggestions are greatly appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:48 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.