Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Hi Build Primers VS 2 part epoxies?
User Name
lost password?   |   register now

Thread: Hi Build Primers VS 2 part epoxies? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-09-2005 10:58 PM
kenseth17 filler on top of epoxy primer or ground baremetal. Not sure about the urethane primer. I was taught to apply filler over ground baremetal, but it is also acceptable to apply it over epoxy primer and many shops I worked in did it that way. The only fillers I apply over urethane primer are the finishing putties that can be applied over paint. I am not sure if it is recommended to apply filler over urethane primer. Many people apply epoxy to baremetal, scuff epoxy and apply there bodyfiller, and when they got it straight, apply more epoxy primer and then urethane filler primer over that.
07-09-2005 10:05 PM
Gearhead forever
Originally Posted by kenseth17
shoot epoxy primer on baremetal and then shoot 2k urethane primer for fill. You only need 1 or 2 coats of epoxy primer.
Do you mean apply any required filler (bondo or spot putty) on top of the 2K primer? I'm assuming you never use filler on bare metal....
07-09-2005 10:03 PM
Gearhead forever Thanks guys....much appreciated.
07-09-2005 07:43 PM
kenseth17 I simple way of explaining a 2k primer or sealer is that it is one that cures chemically by adding a hardener, activator, catalyst. Whatever they happen to call it. It does noy rely on air to cure like a primer that doesn't have an activator that comes with it, A good example being lacquer primers. Thats why you also can get lacquer primer in spray bombs, but a 2k you cannot, it would harden up in the can in a matter of hours if the 2 parts were mixed. The 2 part primers have a pot life, and if you leave them in a spray gun without cleaning it the gun would be pretty much trash if it sat too long. But in the old days when lacquer primer was mainly used at a few shops I worked at they would leave the lacquer primer in the gun overnight and use it the next day. And if the lacquer primer did dry up a little shooting some lacquer thinner through the gun would usually take care of it.
I third the advice, shoot epoxy primer on baremetal and then shoot 2k urethane primer for fill. You only need 1 or 2 coats of epoxy primer.
07-09-2005 05:39 PM
baddbob Definately use an epoxy over the bare metal, sand the metal well with 80 grit to make some nice scratches for the epoxy to adhere to. Clean the metal well before you apply the epoxy. The epoxy will provide the foundation for a quality job.
07-09-2005 03:40 PM
67goat Epoxy Is What You Want To Start With, Then The 2k Primer , It Is A 2 Component Urethane Primer, Also Called Hi Build Or 2k Primer, Some High Build Has Capabilities Of Filling 80 Grit Scratches Easy, I Have Even Used Some Over 40 Grit Scratches Test Patterns, Three To Foar Coats Let Dry Overnight Guide Coat And Start Blocking, Hope This Helps.mike.
07-09-2005 03:35 PM
Gearhead forever
Hi Build Primers VS 2 part epoxies?

Paint newb guy here again. I'd like to prime an area at a time as I finish (mechanically stripping and sandblasting to bare metal) This project is extremely slow moving and I am forced to work on it in sections. Due to the time involved, I don't want to leave the bare metal uncoated and also help covering sanding marks and some smaller rust pits if possible. I'm planning on using AE (?) bc/cc on top.

Any recommendations fro the pros?

PS what is 2K primer? (is that just a trade name like kleenex?)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:06 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.