Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Heads and Intake combo
User Name
Password
lost password?   |   register now

Thread: Heads and Intake combo Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-23-2005 11:33 PM
bracketeer Aluminum for sure. Angle plugs require different headers and are a pain in the a**.
07-23-2005 11:25 PM
strikingthematch Nice car!

AFR is alu. heads...

I agree with what brack. said

For you if your putting money into something it is my mind that you get the best you can afford (within reason)

Thinking is that if at some point this goes from street car to strip car there ya go. Your one step ahead of the game and won't kick yourself in the pants thinking "geezs I jsut put heads on 2 years ago... I saved 300 then but now it will end up costing me twice that!... "

If you can use race gas then the 64 cc heads wouldd be good for you. Mix it with a little pre. gas. The 11:1 comp will make for a really nice set up.

The rpm intake or rpm airgap for sure

ST. plugs are really all you need. Angle plugs where suppose to be for better burn in the combustion chamber but the results are moot.

Now if you just get a cam to tie those together you will have a very nice combo.

Chris
07-23-2005 08:46 PM
black66
parts

Thanks for the reply bracketeer. Yes this is a street car. Here is how it sounds now 66 SS Impala. Now are AFR aluminum or steel? And if it is only a street car would aluminum be a waste of cash?

My pistons are KB 11.2 compression with 64cc heads. What would the compression be if I jumped to 58cc? I have access to all the race gas I need.....

What is the advantage of having angles plugs or straight plugs?

thanks....
07-23-2005 08:32 PM
bracketeer I am assuming this is a street car.....
AFR heads are the best bang for the buck.
Dart would be my second choice.
Edelbrock heads are cheaper but are only good to .575 lift.
Pistons will determine which cc head you need.
Flat tops 64cc. Raised dome 70cc and up depending on dome height.
Intake Perf/RPM or RPM/Airgap for summer driver only.
07-23-2005 07:05 PM
black66
Heads and Intake combo

I have posted about which heads I should get. But I would like some feeback on what heads and intake work best toghether. Here is my setup:

355 SBC
3200 Stall
245 duration .600 Comp roller cam
Camel Hump Heads 2.02/1.60
Torker II Intake
Might Demon 750
Headman Long tube headers
MSD Ignition

My cars runs great. I am switching to a 700R non lockup and 4.56 rear gears. So it is time to get the best heads and intake...

I knew building my motor that my heads do not flow past .500 lift. And I hear that my intake may not be the best..... But the motor was built for free. So at the time I was not complaing....

Are aluminum heads worth the cost over Iron?

How do I determine what cc runners I need for my new heads?

What would be the best cam and intake setup for my cam??

Thanks guys. Looking to purchase the heads and intake asap....

Dave

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:25 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.